- Type of paper
: Book
Title:
- Type of paper
: Paper in book
Title: Sintering
- Authors:
- Markotić, Anto (57483)
- Miloševski, S.
- Viličić, Živan
- Editors
- Viličić, Živan
Publisher: Leksikografski zavod "Miroslav Krleža"
ISBN: 86-7053-026-0
Year: 1992
Pages: from 102 to 109
Number of references: 8
Language: hrvatski
Summary: A short sarvay of a significant procedure concerning
theagglomeration of fine-grained ores and concentrates in
extractivemetallurgy was given.
Also, the sintered metallurgy (powder metallurgy and sinteredmetallurgy
products) were elaborated.
Keywords: Sintering, Process of Sintering, Sinter Characteristics andQualities, Sintering Devices, Sintered Metallurgy, PowderMetallurgy
- Type of paper
: Paper in journal
Title: Behaviour of niobium microllayed steel at the
thermomechanical treatment
- Authors:
- Rešković, Stoja (57806)
- Preloščan, Andrija (38695)
Journal: Metalurgija
Number: 3
ISSN: 0543-5846
Volume: 30
Year: 1991
Pages: from 63 to 73
Number of references: 31
Language: hrvatski
Summary: In the work have been studied melting and
precipitationmechanisms of stable phases of microalloying
elementniobium,especially in the final phase of the
thermomechanicaltreatment.The knowledge of the influence of the
precipitationsinduced by deformation on the processes of
hardening,softeningand variation of natural deformation resistance of
microalloyedsteel have been extended.By controlled process of hot
plasticdeformation of microalloyed steel in
industrialconditions,satisfactory structure properties and homogeneity
ofrolled product have been obtained.The mechanisms of solution andniobium
carbonitrides precipitation have been correlated andexplained with the
mechanisms of the static and dynamicrecrystallization.
Keywords: Microalloyed, Niobium, Steel, Termomechanical treatment
- Type of paper
: Paper in journal
Title: Hot rolled strip production from the niobium-micro-alloyed
steel
- Authors:
- Rešković, Stoja (57806)
- Novosel-Radović, Vjera (33706)
- Fried, Željko
Journal: Metalurgija
Number: 4
ISSN: 0543-5846
Volume: 30
Year: 1991
Pages: from 155 to 60
Number of references: 12
Language: hrvatski
Summary: The results of the hot rolled strip production
possibilities fromthe niobium microalloyed steel in the Metallurgical
Works"Željezara Sisak" - Sisak are shown in the work. Eleven
differentvariants of the thermomechanical treatment have been carried outon
eleven steel melts of the same basic chemical analysis. Thestrips of
different thicknesses of 2 to 4 mm have been rolled andstructural,
mechanical and technological properties have beentested. Satisfactory hot
rolled strip structure properties andhomogeneity have been achieved by the
control process of hotplastic deformation in industrial conditions.
Keywords: Hot rolled strip, Microalloyed steel
- Type of paper
: Paper in journal
Title: Testing of weld quality of niobium microalloyed steel
tubes by HF process
- Authors:
- Rešković, Stoja (57806)
- Trujić, V.
Journal: Zavarivanje
Number: 5
ISSN: 0044-1902
Volume: 35
Year: 1992
Pages: from 191 to 197
Number of references: 11
Language: hrvatski
Summary: Testing of weld quality of the niobium microalloyed
precisionseam steel tubes joined by HF process has been carried. Besidethe
standard methods, weld quality and form of niobium in basemetal and weld
metal has been also tested by electrolyticinsulation, phase identification
and electron scanningmicroanalysis. Results are identicating good seam
quality andgood weldability of the Nb alloyed steel when HF process
isapplied.
Keywords: Niobium microalloyed steel; HF welding; tube
- Type of paper
: Paper in journal
Title: Testing of weld quality of niobium microalloyed steel
tubes by HF process
- Authors:
- Rešković, Stoja (57806)
- Trujić, V.
Journal: Zavarivanje 35
Number: 5
ISSN: 0044-1902
Volume: 35
Year: 1992
Pages: from 191 to 197
Number of references: 11
Language: hrvatski
Summary: Testing of weld quality of the niobium microalloyed
precisionseam steel tubes joined by HF process has been carried. Besidethe
standard methods, weld quality and form of niobium in basemetal and weld
metal has been also tested by electrolyticinsulation, phase identification
and electron scanningmicroanalysis. Results are identicating good seam
quality andgood weldability of the Nb alloyed steel when HF process
isapplied.
Keywords: Niobium microalloyed steel, HF welding, Tube
- Type of paper
: Paper in journal
Title: Thin Walled Scafold Niobium Microalloyed Steel Tubes
- Authors:
- Rešković, Stoja (57806)
Journal: Strojarstvo
Number: 6
ISSN: 0562-1887
Volume: 34
Year: 1992
Pages: from 243 to 246
Number of references: 8
Language: hrvatski
Summary: The paper presents the research results of niobium
microalloyedsteel application in production of hot rolled strips for
weldedtubes scaffold construction. The obtained results sugges thatniobijum
microalloyed steel tubes, when reduced for 0,6 mm, havestill properties
remarkably better than the same tubes made fromsteel of quality Č.0561. A
tube mass reduction is achieved, i.e.a saving in material for about 20 %.
Keywords: Scaffold Construction; Microalloying; Niobium; Steel tube
- Type of paper
: Paper in journal
Title: Thin Walled Scafold Niobium Microalloyed Steel Tubes
- Authors:
- Rešković, Stoja (57806)
Journal: Zavarivanje
Number: 6
ISSN: 0562-1887
Volume: 34
Year: 1992
Pages: from 243 to 246
Number of references: 8
Language: hrvatski
Summary: This paper presents the research results of niobium
microalloyedsteel application in production of hot rolled strips for
weldedtubes scaffold construstion. The obtain results suggest thatniobium
microalloyed steel tubes, when reduced for 0,6 mm, havestill properties
remarkably better than the same tubes made fromsteel of quality Č.0561. A
tube mass reduction is achieved, i.e.a saving in material for about 20 %.
Keywords: Scaffold Construction, Microalloying, Niobium, Steel Tube
- Type of paper
: Paper in journal
Title: Thermogravimetric and laboratory investigations of
magnetite concentrate reduction by solid reducers
- Authors:
- Rešković, Stoja (57806)
Journal: Iron & Steelmaking
Number: 1
ISSN: 0301-9233
Volume: 18
Year: 1991
Pages: from 51 to 57
Number of references: 12
Language: engleski
Summary: This paper gives characteristics of some solid reducers
ofYugoslavia: their technical and elementary analyses and chemicalanalysis
of ashes. Insight into the behavior of coals duringheating has been
obtained by thermogravimetric investigations inneutral atmospheres. Based
on established characteristics, themost favorable reducers have been chosen
and mixtures preparedwith magnetite concentrate from Majdanpek. The
proceedings of thereduction of these mixtures have been investigated on
athermoscale. Obtained results have pointed out the best reducerfor the
production of metallized pellets, which has also beenchecked experimentally
under laboratory conditions.
Keywords: Magnetite concentrate, Reduction, Solid reducer, Metallized pellets
- Type of paper
: Paper in journal
Title: Direct Reduction and Smelting Redukction Processes Today;
Part II Smelting Reduction of Pig Iron
- Authors:
- Rešković, Stoja (57806)
- Novosel-Radović, Vjera (33706)
- Preloščan, Andrija (38695)
- Fried, Željko
Journal: Iron & Steelmaking
Number: 7
ISSN: 0350-2627
Volume: 42
Year: 1991
Pages: from 488 to 493
Number of references: 18
Language: srpsko-hrvatski
Summary: Smelting reduction appears to be very attractive
alternative todirect reduction. The intensive and comprehensive
researchcarried out into this matter so far has brought about
thedevelopment of several processes to the stage of pilot
plantapplications. Once the importance of these processes has
beenestablished, the paper goes on to consider the
classification,description and adventages and disadventages of the same.
Specialattention has been paid to further developments and ad indicationis
given of the possible use of these processes in iron and steelmetallurgy.
Keywords: Smelting Reduction, Pig Iron, Processes, Development
- Type of paper
: Paper in journal
Title: Direct Reduction and Smelting Reduction Processes today;
Part I: Direct Reduction of Iron
- Authors:
- Slošić, V.
- Markotić, Anto (57483)
Journal: Iron & Steelmaking
Number: 5
ISSN: 0350-2627
Volume: 42
Year: 1991
Pages: from 357 to 360
Number of references: 7
Language: srpsko-hrvatski
Summary: The paper gives a systematic review of the whole state in
thedirect reduction (DR) of iron. Shows to a crossed way. AllSignificant
processes and their principal features areemphasized. Furthermore, the
scope of processes applicability atpresent is discussed. Problems that may
be encountered in thisfield and trends in further development are also
anticipated.
Keywords: Direct Reduction, Iron, Processes, Development
- Type of paper
: Paper in journal
Title: Thermogravimetric and laboratory investigations of
magnetite concentrate reduction by solid reducers
- Authors:
- Markotić, Anto (57483)
- Čurković, A.
- Malina, Marijan (92381)
- Živković, V.
- Županić, S.
Journal: Iron & Steelmaking
Number: 1
ISSN: 0301-9233
Volume: 18
Year: 1991
Pages: from 51 to 57
Number of references: 12
Language: engleski
Summary: This paper gives characteristics of some solid reducers
ofYugoslavia: their technical and elementary analyses and chemicalanalysis
of ashes. Insight into the behavior of coals duringheating has been
obtained by thermogravimetric investigations inneutral atmospheres. Based
on established characteristics, themost favorable reducers have been chosen
and mixtures preparedwith magnetite concentrate from Majdanpek. The
proceedings of thereduction of these mixtures have been investigated on
athermoscale. Obtained results have pointed out the best reducerfor the
production of metallized pellets, which has also beenchecked experimentally
under laboratory conditions.
Keywords: Magnetite concentrate; Reduction; Solid reducer; Metallized pellets
- Type of paper
: Paper in journal
Title: Programme of Reconstruction and Development of Steel
Manufacturing Industry in Croatia
- Authors:
- Markotić, Anto (57483)
- Čurković, A.
- Malina, Marijan (92381)
- Živković, V.
- Županić, S.
Journal: Metalurgija
Number: 3
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 81 to 85
Number of references: 10
Language: hrvatski
Summary: Essentially changed market environment of steel
products,difficulties in business operations and requested restructuringof
steel manufacturing industry in Croatia induced a desing ofprogramme for
reconstruction and development wich will definestrategy of over coming
existing difficulties bearing in mind thenew circumstances (independent
state). Also, needed investmentsinto the perspective development and
profitable products andproducts for home market are considered. Forecast
was also thereduction of country's balance of payments regarding steel
importfor the home needs of metal manufacture.
Keywords: Steel fabrication, Steel, Market, Production, Processing, Reconstruction, Development
- Type of paper
: Paper in journal
Title: Direct Reduction and Smelting Reduction Processes Today;
Part I: Direct Reduction of Iron
- Authors:
- Trujić, V.
- Markotić, Anto (57483)
Journal: TEHNIKA - Rudarstvo, geologija i metalurgija
Number: 5
ISSN: 0350-2627
Volume: 42
Year: 1991
Pages: from 357 to 360
Number of references: 7
Language: srpsko-hrvatski
Summary: The paper gives a systematic review of the whole state in
thedirect reduction (DR) of iron. Shows to a crossed way. Allsignificant
processes and their principal features areemphasized. Furthermore, the
scope of processes applicability atpresent is discussed. Problems that may
be encountered in thisfield and trends in further development are also
anticipated.
Keywords: Direct reduction Iron Processes Development
- Type of paper
: Paper in journal
Title: Some Quality Aspects of the Pig Iron with Various Content
of Manganese
- Authors:
- Trujić, V.
- Markotić, Anto (57483)
Journal: Metalurgija
Number: 3
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 105 to 108
Number of references: 7
Language: hrvatski
Summary: By decreasing sulphur activity coefficient in metal and
bystabilizing of carbide structure, manganese influences favourablythe pig
iron quality. By continuous adding of manganese ore tothe blast furnace
charge, mathemetical dependence of manganeseand sulphur concentracion in
metal in the entire interval ofconcentracion changes in the observed metals
was noticed.Selective analysis of the dependence of high and low
manganeseconcentrations in metal and sulphur shows that stronger
manganeseeffect on sulphur concentration decrease is evident at
theincreased manganese concentration in metal.
Keywords: Pig Iron, Quality, Manganese, Sulphur
- Type of paper
: Paper in journal
Title: Direct Reduction and Smelting Reduction Processes Today;
Part II: Smelting Reduction of Pig Iron
- Authors:
- Ivaniš, Stjepan (17251)
- Ferketić, Vladimir (11634)
- Vuković, Dušan
Journal: TEHNIKA - Rudarstvo, geologija i metalurgija
Number: 7
ISSN: 0350-2627
Volume: 42
Year: 1991
Pages: from 488 to 493
Number of references: 18
Language: srpsko-hrvatski
Summary: Smelting reduction appears to be a very attractive
alternative todirect reduction. The intensive and comprehensive
researchcarried out into this matter so far has brought about
thedevelopment of several processes to the stage of pilot
plantapplications.
Once the importance of these processes has been established, thepaper goes
on to consider the classification, description andadventages and
disadventages of the same.
Special attention has been paid to further developments and anindication is
given if the possible use of these processes iniron and steel metallurgy.
Keywords: Smelting reduction Pig iron Processes Development
- Type of paper
: Paper in journal
Title: Desulphurization of Pig Iron by Means of Magnesium Core
Wire Insertion
- Authors:
- Ivaniš, Stjepan (17251)
- Ferketić, Vladimir (11634)
- Vuković, Dušan
Journal: Metalurgija
Number: 1
ISSN: 0543-5846
Volume: 30
Year: 1991
Pages: from 25 to 31
Number of references: 3
Language: hrvatski
Summary: Industrial experiments of pig iron desulphurization have
beencarried out by means of inserting MgCaC2 core wire into melt. Dueto a
few number of experiments it was not possible to quantifyany special
indexes. However, it was estimated that regarding tosome reqests on steel
quality we can build on this desulphurizingtechnology.
Keywords: Pig Iron, Desulphurization, Magnesium core wire
- Type of paper
: Paper in journal
Title: Desulphurization slag properties in the blast furnace of
Željezara Sisak
- Authors:
- Markotić, Anto (57483)
- Slošić, V.
- Malina, Marijan (92381)
- Čurković, A.
- Živković, V.
- Županić, S.
Journal: Metalurgija
Number: 3
ISSN: 0543-5846
Volume: 30
Year: 1991
Pages: from 91 to 96
Number of references: 11
Language: hrvatski
Summary: The sulphide slag capacity has been estimated and the
reasons forits unexploatation have been pointed out. The way of the
slagcompound choice has been suggested on the basis of the statediagram
with viscosity, sulphide capacity and slag stabilitylimit. The suggested
way has to ensure the content of the pigiron sulphur to be under 0,035 %.
Keywords: Slag, Blast furnace, Desulphurization
- Type of paper
: Paper in journal
Title: The identification of surface inclusions in steel ingot
and tube
- Authors:
- Krajcar, Josip (23143)
- Dmitrović, Radana
- Iharoš, Ana
- Novosel-Radović, Vjera (33706)
- Ivančan, Anka (79316)
- Đuričić, V.
Journal: Metalurgija
Number: 1
ISSN: 0543-5846
Volume: 30
Year: 1991
Pages: from 39 to 46
Number of references: 9
Language: hrvatski
Summary: The inclusions in the region of surface defects in ingot
and onthe outer surface of seamless tubes were examined. It wasdetermined
that the rough inclusions come from the refractoriesused in the casting pit
and from the casting powder.
Keywords: Surface Inclusions, Ingot Steel, Tube Steel
- Type of paper
: Paper in journal
Title: Surface defects on ingots and their impact on the outer
surface of seamless tubes
- Authors:
- Krajcar, Josip (23143)
- Plepelić, J.
- Butorac, Juraj
- Ivančan, Anka (79316)
- Iharoš, Ana
- Vuković, Dušan
- Ferketić, Vladimir (11634)
Journal: Metalurgija
Number: 3
ISSN: 0543-5846
Volume: 30
Year: 1991
Pages: from 97 to 108
Number of references: 22
Language: hrvatski
Summary: The outer surface defect of seamless tubes rolled from
ingotswere investigated and it was stated that the cracks and shells
ontubes are caused by the surface inclusions and blowholes oningots.
Keywords: Tubes, Seamless, Defects, Ingots
- Type of paper
: Paper in journal
Title: Problems with continuous casting of steel after
restructuring and modernization of the plants in the Sisak Steel Works
- Authors:
- Krajcar, Josip (23143)
- Ferketić, Vladimir (11634)
- Vuković, Dušan
Journal: Metalurgija
Number: 4
ISSN: 0543-5846
Volume: 30
Year: 1992
Pages: from 149 to 153
Number of references: 11
Language: hrvatski
Summary: In the restructured Steel plant in Sisak two existing
continuouscasting machines will be used. The both machines will
bemodernized, one will be reconstructed (enlargement of radius) forcasting
blooms for large diameter tubes which are now rolled fromingots. All
charging materials for seamless tubes will becontinuously cast.
Keywords: Continuous Casting, Restructuring, Modernization
- Type of paper
: Paper in journal
Title: Surface defects on Seamless Tubes Due to Raw Materials
- Authors:
- Krajcar, Josip (23143)
- Ferketić, Vladimir (11634)
- Vuković, Dušan
- Ivančan, Anka (79316)
- Butorac, Juraj
- Iharoš, Ana
Journal: TEHNIKA - Rudarstvo, geologija i metalurgija
Number: 1
ISSN: 1318-0010
Volume: 26
Year: 1992
Pages: from 94 to 96
Number of references: 14
Language: hrvatski
Summary: The external and internal quality of seamless tubes in the
SisakSteelwork is unsatisfying. The tubes are manufactured fromingots,
continuous cast blooms and rooled billets. The defectscoming from raw
materials (semis) are more frequent on tubesrolled from ingots, due to the
poor surface and in adequate topform. The major share of surface defects
originates frominclusions caused mostly by worse pit refractories. A
deepshrinkage cavity is caused by casting in big-and-dawn moldswithout hot
tops. The surface of tubes from continuous castblooms is not much better
because of the large frequency ofsurface inclusions and internal cracks.
Keywords: Surface defects, Seamless tubes
- Type of paper
: Paper in journal
Title: The Causes of surface Defects and the Possibilities to
improve the surface quality of ingots for seamless tubes
- Authors:
- Krajcar, Josip (23143)
- Kendi, Želimir
- Ivančan, Anka (79316)
- Vuković, Dušan
- Ferketić, Vladimir (11634)
Journal: Metalurgija
Number: 1
ISSN: 0543-5846
Volume: 31
Year: 1992
Pages: from 35 to 41
Number of references: 14
Language: hrvatski
Summary: On the basis of operation and laboratory tests the causes
ofsurface defects on ingots for seamless tubes in Steelwork Sisakare
determined and the possibilities to improve the surfacequality are given.
Keywords: Surface defects, Ingots, Seamless tubes
- Type of paper
: Paper in journal
Title: Surface Defects on Seamless Stell Tubes Carried over by
Charge Materials
- Authors:
- Krajcar, Josip (23143)
- Vuković, Dušan
- Ivančan, Anka (79316)
- Kovačić, Ivan
- Ferketić, Vladimir (11634)
- Butorac, Juraj
- Iharoš, Ana
- Belošević, Zvonimir
- Babić, V.
Journal: Metalurgija
Number: 2
ISSN: 0543-5846
Volume: 31
Year: 1992
Pages: from 83 to 96
Number of references: 36
Language: hrvatski
Summary: The external and internal surface quality of seamless tubes
isunsatisfying and tends to aggravation. The defects coming fromcharge
materijals are mostly frequent on tubes manufactured fromingots, due to the
worse surface and inadequate top form. Thesurface quality of tubes from
continuous cast blooms are fromprerolled billets is not much better. With
the existingtechnology considerable improvements are not possible, but
theprevious obtained results must be assured.
Keywords: Seamless tubes, Defects, Surface, Steel
- Type of paper
: Paper in journal
Title: The future crude steel production in Sisak
- Authors:
- Krajcar, Josip (23143)
Journal: Metalurgija
Number: 4
ISSN: 0543-5846
Volume: 31
Year: 1992
Pages: from 135 to 138
Number of references: 20
Language: hrvatski
Summary: The semis for seamless tubes at the Sisak Steelworks will
befuther produced in the own steel plant, which has to be
soonrestructurized. Instead of the present three furnaces, two OH andone
little EAF, only one modern EAF will operate which would havesuch capacity
in order to use the existing plant and equipmentfor transport and casting.
The steel will be continuous cast andtherefore one of the existing machines
will be adapted forcasting blooms and the other for billets. More processes
laddlemetallurgy will be used.
Keywords: Steel, Crude, Production
- Type of paper
: Paper in journal
Title: Lubricating ability of casting powders at continuous
casting of steel
- Authors:
- Krajcar, Josip (23143)
- Ferketić, Vladimir (11634)
- Ivančan, Anka (79316)
Journal: Hutnicke listy
Number: 9
ISSN: 0018-8069
Volume: 47
Year: 1992
Pages: from 1 to 5
Number of references: 21
Language: slovački
Summary: The friction force in the mould during continuous casting
wascalculated from the power of the oscillator motor measured in theidle
motion and during casting of different semiproduct withdifferent casting
powders. The friction force rises atinsufficient powder addition and at the
change of the castingspeed, the change of conventional casting powders has
a lowimpact.
Keywords: Continuous Casting, Casting Powder, Surface Quality
- Type of paper
: Paper in journal
Title: Directly reduced iron in steel production in electric arc
furnace
- Authors:
- Krajcar, Josip (23143)
- Kovačič, Vesna
Journal: Metalurgija
Number: 1
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 37 to 42
Number of references: 21
Language: hrvatski
Summary: The processes giving the gigher production are short
described.The characteristics of the row materials for the electric
arcfurnace (EAF): the steel scrap, the pig iron and the directlyreduced
iron (DRI), are compared. The perspectives for the futuredevelopment are
given. DRI becomes more interesting in theRepublic of Croatia because of
the shortage of scrap of higherquality classes.
Keywords: Steel, Production, Iron, Directly Reduced
- Type of paper
: Paper in journal
Title: Steel scrap as raw material for steel production in
electric arc furnaces
- Authors:
- Krajcar, Josip (23143)
Journal: Metalurgija
Number: 3
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 97 to 100
Number of references: 20
Language: hrvatski
Summary: The different kinds of steel scrap as raw material in
electricarc furnaces require an adequate preparation. A modern
scrappreparation can be effcient only for large quantities. In theRepublic
of Croatia at first the quantities of differentavailable kinds of scrap and
for getting the optimal annualproduction, the import of additional ones
have to be determined.Based on this a suitable scrap preparation and the
need ofcooperation with neighbouring countries can be planned.
Keywords: Steel Scrap, Steel, Electric Arc Furnace
- Type of paper
: Paper in journal
Title: The role of ladle metallurgy in the modern steel
production
- Authors:
- Krajcar, Josip (23143)
Journal: Metalurgija
Number: 3
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 87 to 92
Number of references: 28
Language: hrvatski
Summary: The ladle metallurgy is indispensable in the modern
steelproduction. It enables in all steel plants the qualityimprovement and
in the electrical steel plants the increase ofproductivity and the
reduction of production costs. In the paperthe processes for the removing
of impurities and for the increaseof the cleanliness of steel are briefly
exposed, afterwards thenew tasks of the ladle metallurgy are pointed out.
Keywords: Ladle Metallurgy, Crude Steel Production
- Type of paper
: Paper in journal
Title: Evalution of casting powders by means of melting curves
- Authors:
- Ivančan, Anka (79316)
- Krajcar, Josip (23143)
Journal: TEHNIKA - Rudarstvo, geologija i metalurgija
Number: 1
ISSN: 1318-0010
Volume: 27
Year: 1993
Pages: from 33 to 38
Number of references: 15
Language: hrvatski
Summary: The melting curves of casting powders for continuous and
ingotcasting in the as delivered state and with addition of alumina,fire
clay and their mixture up to 20 % are described. Thepossibility of the
simulation of the powder action during castingon the base of the melting
behaviour is treated. The powders forcontinuous casting in this manner can
be fully evaluated, but theones for ingot casting, because of the reactions
of molten steelwith the refractories, only partially.
Keywords: Steel, Continuous Casting, Ingot Casting, Casting Powder, Melting Curves
- Type of paper
: Paper in journal
Title: The preparation of rolling scale for the use in the
sintering
- Authors:
- Grgurač, Antun (148473)
- Šolić, Mira
- Tadić, Lidija
- Klasnić, Zlatko
Journal: Metalurgija
Number: 3
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 109 to 115
Number of references: 8
Language: hrvatski
Summary: The rolling scale as a usefull secondary raw material must
beprepared for the recycling process. In this work the bases of thedeoiling
process and the characteristics of scale from differentorigin places are
given; the laboratory and the production testare presented and the
acchieved results commented. It was statedthat the deoiling with lime can
be used in the sintering processof the blast furnace charge. The results
can be used in theconsideration of the use of scale for other applications
(chargefor the electric arc furnace).
Keywords: Rolling Scale, Deoiling, Sintering
- Type of paper
: Paper in journal
Title: Hardenability testing of low alloyed chromium steels
modified by molybdenium and niobium
- Authors:
- Gojić, Mirko (63390)
- Preloščan, Andrija (38695)
- Malina, Marijan (92381)
Journal: Metalurgija
Number: 4
ISSN: 0543-5846
Volume: 30
Year: 1991
Pages: from 160 to 165
Number of references: 9
Language: hrvatski
Summary: Low alloyed steels containing chromium and molybdenum have
thewidespread field of application, specially in the production ofoil
country tubular goods which are used for exploatation of thedeep oil and
gas deposits and are exposed to severe corrosionconditions. One of the most
important conditions in achieving thenecessary properties (particularly
microstructure) of the product(pipe) is hardenability. The study
investigates hardenability onthe basis of Jominy method and calculations of
optimalaustenizing temperature of the following steel grades: 0,4 % Cand
1,1 % Cr; 0,4 % C, 1,0 % Cr and 0,25 % Mo; 0,4 % C, 1,0 % Cr,0,7 % Mo and
0,017 % Nb.
Keywords: Hardenability, Chromium Steels
- Type of paper
: Paper in journal
Title: Ilustration the book "Material steel" edited prof. dr.
Pavla Pavlovića
- Authors:
- Gojić, Mirko (63390)
Journal: Metalurgija
Number: 1
ISSN: 0543-5846
Volume: 30
Year: 1991
Pages: from 53 to 54
Language: hrvatski
- Type of paper
: Paper in journal
Title: Evaluation of Mn - V steel tendency to hydrogen
embrittlement
- Authors:
- Gojić, Mirko (63390)
- Balenović, Marijan (139043)
- Kosec, Ladislav
- Unkić, Faruk (57790)
- Malina, Jadranka (83026)
Journal: TEHNIKA - Rudarstvo, geologija i metalurgija
Number: 4
ISSN: 1318-0010
Volume: 26
Year: 1992
Pages: from 343 to 349
Number of references: 14
Language: engleski
Summary: Results of mechanical properties and evaluation of dendency
ofseamless tubes in as rolled and heat treated condition, producedfrom
medium-carbon Mn-V steel to hydrogen embrittlement by methodof cathode
polarization at the constant current density of 4,0mA/cm2 are presented in
this paper.
Keywords: Steel, Hydrogen, Embrittlement, Heat Treatment
- Type of paper
: Paper in journal
Title: Hydrogen embrittlement evaluation of duplex stainless
steel for oil industry
- Authors:
- Gojić, Mirko (63390)
- Malina, Jadranka (83026)
- Ivaniš, Krešimir
Journal: Nafta
Number: 6
ISSN: 0027-755
Volume: 43
Year: 1992
Pages: from 313 to 321
Number of references: 12
Language: hrvatski
Summary: The results of investigations have demonstrated that tubing
madefrom steel investigated is characterized with high SSC resistance,
expressed with sigma - value of 84 % yield strength, as well aslow hydrogen
embrittlement susceptibility with embrittlementindex F = 26,2 %.
Keywords: Duplex Stainless Steel, Corrosion, Hydrogen Embrittlement, Treshold Stress, Cathodic Polarization
- Type of paper
: Paper in journal
Title: Alloys with the shap memory effect
- Authors:
- Gojić, Mirko (63390)
Journal: Metalurgija
Number: 2
ISSN: 0543-5846
Volume: 31
Year: 1992
Pages: from 77 to 82
Number of references: 21
Language: hrvatski
Summary: Besides the normal properties some metal materijals show
theproperty of shape memory. The shape memory effect is theremembrance of
the previously introduced material shape, and inphysical aspect it is the
consequence of martensite phasetransformation in the structure of
homogenous substance. In thepaper the survey of the alloys with shape
memory effect andcorresponding phase transformation mechanisms as well as
theirproperties and possibilities of application have been presented.
Keywords: Alloys, Memory, Shape
- Type of paper
: Paper in journal
Title: The forms of corrosion damages of pipes for oil industry
- Authors:
- Gojić, Mirko (63390)
- Kosec, Ladislav
- Unkić, Faruk (57790)
Journal: Nafta
Number: 12
ISSN: 0027-755
Volume: 43
Year: 1992
Pages: from 591 to 599
Number of references: 17
Language: hrvatski
Summary: In this paper, the possible forms of the corrosion damages
of thepipes being used in oil and gas exploatation and transport,production
and future development of the steel pipes in Croatiaare mentioned.
Keywords: Damage, Pipes, Corrosion, Stress
- Type of paper
: Paper in journal
Title: The influence of heat treatment on sulfide stress
corrosion cracking at low alloy steel tubing
- Authors:
- Gojić, Mirko (63390)
- Malina, Jadranka (83026)
- Malina, Marijan (92381)
- Ivaniš, Krešimir
Journal: Kemija u industriji
Number: 5
ISSN: 0022-9830
Volume: 42
Year: 1993
Pages: from 139 to 144
Number of references: 14
Language: hrvatski
Summary: In this paper, the SSCC susceptibility of comercial Cr-Mo
steeland Mn-Cr tubing steel is analyzed.
The test results show that normalized and tempered Cr-Mo steeltubing of the
chemical composition presented in the paper are notto be recommended for
the application in oil industry because ofthe small resistance to SSCC.
Keywords: Heat Treatment, Sulfide Stress Corrosion, Low Alloyed Steel
- Type of paper
: Paper in journal
Title: Critical stress of low alloy Mn-V and Cr-Mo steel tubing
- Authors:
- Gojić, Mirko (63390)
- Balenović, Marijan (139043)
Journal: Nafta
Number: 11
ISSN: 0027-755
Volume: 44
Year: 1993
Pages: from 617 to 625
Number of references: 11
Language: engleski
Summary: The testing results show that tubing in as-rolled condition
has apoor SSCC resistance (low critical stresses) while, by quenchingand
tempering at temperatures 700 - 720 C, high SSCC resistanceis achieved,
especially by quenching in oil.
Keywords: Critical Stress, Tubing, Corrosion, Heat Treatment
- Type of paper
: Paper in journal
Title: Metallic glasses
- Authors:
- Gojić, Mirko (63390)
Journal: Metalurgija
Number: 4
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 177 to 182
Number of references: 47
Language: hrvatski
Summary: This work gives an overview of the production ways and
metallicglasses sorts, as well as their mechanic, electric, magnetic
andcorrosion characteristics with the possibilities of theirapplications.
Keywords: Metallic Glasses, Properties, Application
- Type of paper
: Paper in journal
Title: Application of dilatometer LK.02 in material research
- Authors:
- Gojić, Mirko (63390)
Journal: Zavarivanje
Number: 1
ISSN: 0562-1887
Volume: 35
Year: 1993
Pages: from 77 to 81
Language: hrvatski
Summary: The paper deals with operating and working possibilities
ofhigh-speed cooling dilatometer LK.02. There were analyzed theprinciple of
work and working conditions as well as differentcooling rates required for
diagrams of continuous and isothermalcooling.
Keywords: Cooling Rate, Dilatometer, High-speed Quenching, Dilatometry Analysis, Heat Treatment, Isothermal Cooling
- Type of paper
: Paper in journal
Title: SEM analysis of fracture surfaces of low alloyed Cr-Mo-Nb
steel
- Authors:
- Gojić, Mirko (63390)
Journal: Periodicum biologorum
Number: 2
ISSN: 0031-5362
Volume: 95
Year: 1993
Pages: from 275 to 276
Number of references: 3
Language: engleski
Summary: The fracture surfaces of specimens are tested after
cathodicpolarization by a scanning electron microscope. The specimens arein
as-rolled (without heat treatment) and heat treated byquenching and
tempering.
Keywords: Low Alloyed Steel, Fractured Surface, Cathodic Polarisation
- Type of paper
: Paper in journal
Title: From a Department of Mining and Metallurgy of a Technical
Faculty in Zagreb up to a Metallurgical Faculty in Sisak
- Authors:
- Črnko, Josip (57413)
Journal: Metalurgija
Number: 1
ISSN: 0543-5846
Volume: 30
Year: 1991
Pages: from 51 to 53
Number of references: 8
Language: hrvatski
Summary: The paper presents the developement of a
degree-grantingeducation in mrtallurgy as a discipline on
Chemical-engineeringDepartment of a High Technical Scool in Zagreb up to
theformation of an autonomous degree-granting institution -Metallurgical
Fakulty in Sisak.
Keywords: Metallurgy, Degree-Granting Education, Developement and Institutions
- Type of paper
: Paper in journal
Title: Choice of the means of liquid fuel dispersion for high
temperature open-hearth furnace
- Authors:
- Kundak, Mijo (24642)
- Črnko, Josip (57413)
Journal: Goriva i maziva
Number: 3
ISSN: 0350-350
Volume: 30
Year: 1991
Pages: from 133 to 148
Number of references: 7
Language: hrvatski
Summary: The influence for the liquid fluid quality upon both the
choiseof means of its dispersion and the open-hearth furnace energyload,
which effects the duration of steel production process, hasbeen studied.
The degree of flame blackness during the combustionof masut used for
fueling the stated furnaces in Sisak Ironworks,produced by Oil Refinery
Sisak-INA Zagreb, has been defined bymeasuring. Based on the facts of the
flame blackness there hasbeen learned that natural gas cannot be used as a
means ofdispersion of that masut.
Keywords: Liquid fuels, Choice of the means of dispersion, High temperature fire places, Open-hearth furnacess
- Type of paper
: Paper in journal
Title: Interpretation of the heat decarburisation speed in the
real conditions
- Authors:
- Kundak, Mijo (24642)
Journal: Metalurgija
Number: 4
ISSN: 0543-5846
Volume: 30
Year: 1991
Pages: from 125 to 130
Number of references: 8
Language: hrvatski
Summary: This paper presents the decarburisation speed in the
laboratoryconditions. These experiences are used in interpretation of
thedecarburisation speed in the refining phase that is determined bymeans
of the flue gas in the real conditions of the steelproduction by the
open-heart process. Interpretation of thedecarburisation speed on the basis
of the flue gas analysis issuitable for the energetic conductance of the
melt heating.
Keywords: Decarburisation speed, Melt heating, Open-hearth furnace
- Type of paper
: Paper in journal
Title: The Mathematical Model of the Cooler of Continuous Casting
Steel Semiproducts
- Authors:
- Lazić, Ladislav (105552)
- Črnko, Josip (57413)
- Jurković, Zvonimir (130276)
- Cvitković, Mirko
Journal: Metalurgija
Number: 4
ISSN: 0543-5846
Volume: 30
Year: 1991
Pages: from 119 to 123
Number of references: 4
Language: hrvatski
Summary: The dwo-dimensional mathematical model of the cooler
ofcontinuous casting steel semiproducts with natural and forced aircooling
is temperature with time as a function of air streamvelocity and distance
between semiproducts.
Keywords: Cooler, Model, Mathematical
- Type of paper
: Paper in journal
Title: Computer Simulation of Solidification of Complex Geometry
Castings
- Authors:
- Grozdanić, Vladimir
- Črnko, Josip (57413)
Journal: Železarski zbornik
Number: 4
ISSN: 0372-8633
Volume: 25
Year: 1991
Pages: from 149 to 158
Number of references: 3
Language: hrvatski
Summary: The soldification simulation of the casting of reletively
complexgeometry, low-carbide steel valve housing, has been presented inthe
paper. Mathematical model has been based on physicalrealistic assumptions,
and has been solved by finite differencemethod - implicit alternating
directions method. Thesolidification simulation of the casting of
relatively complexgeometry which is a common example in foundry practice,
enablesthe improvement of our knowledge about solidification process
inthese casting, and points in a modern and scientific way to thepoints
where defects occurrence is possible and in this way thecasting is not
necessary.
Keywords: Casting, Soldification, Steel, Simulation
- Type of paper
: Paper in journal
Title: Contribution to the leading of melting bath heating in
refining by means of waste gas analysis
- Authors:
- Kundak, Mijo (24642)
Journal: Metalurgija
Number: 1
ISSN: 0543-5846
Volume: 31
Year: 1992
Pages: from 7 to 13
Number of references: 3
Language: hrvatski
Summary: By means of the model, the optimal necessary fuel floe mass
forcontinuous heating control of the cast in the refining dependenton
decarbonization speed and another influent parameters withoutmeasuring of
its temperature was studied on the basis of theenergetic balance in the
upper part of the open-hearth furnace.
Keywords: Leading, Refining, Waste gas, Open-hearth furnace
- Type of paper
: Paper in journal
Title: Basic characteristics of the heating furnace modernization
in rolling mills for hot processing of steel
- Authors:
- Črnko, Josip (57413)
Journal: Metalurgija
Number: 2
ISSN: 0543-5846
Volume: 31
Year: 1992
Pages: from 71 to 76
Number of references: 23
Language: hrvatski
Summary: The paper gives a survey of technical and technological
solutionsapplied to heating furnaces in rolling mills for hot processingof
steel in the last 15-20 years.
Keywords: Furnaces, Heating, Modernization, Steel
- Type of paper
: Paper in journal
Title: The influence of the change of productivity and frequency
of isolationmaintenance on the heat consumption in a pusher-type furnace
- Authors:
- Horbaj, Peter
- Črnko, Josip (57413)
- Lazić, Ladislav (105552)
Journal: Hutnicke listy
Number: 9
ISSN: 0018-8069
Volume: 47
Year: 1992
Pages: from 26 to 28
Number of references: 7
Language: češki
Summary: The paper presents the results of the analysis of the
influenceof a pusher-type furnace productivity increase on the decrease ofa
specific heat energy consumption. As it has been analyticallyfound and
verified in operating practice, if the furnaceproductivity increases from
37 to 61 t/h, the specific heatenergy consumption decreases for about 18
%. By increasing thefrequency of isolation maintenance of a pusher-type
furnace, aspecific heat energy consumption would decrease, which is
possible to acheave by a better month and week planning ofrolling.
Keywords: Pusher-type furnace, Maintenance, Energy, Consumption, Ecology
- Type of paper
: Paper in journal
Title: Optimization of Heating Process in Rolling Mill Sectional
Furnace
- Authors:
- Lazić, Ladislav (105552)
Journal: Hutnicke listy
Number: 9
ISSN: 0018-8069
Volume: 47
Year: 1992
Pages: from 38 to 42
Number of references: 5
Language: slovački
Summary: Determination of optimum furnace heating parameters of
asectional rolling mill high - speed tube heating furnace bysimulating a
heating process using mathematical model.
Keywords: Mathematical model, Sectional furnace, Heating parameters
- Type of paper
: Paper in journal
Title: The dependence of the heat energy consumption upon the
working intensity and the frequenty of the isolation maintenance of a
pusher - type furnace
- Authors:
- Črnko, Josip (57413)
Journal: Yournal of Materials Processing Technology
Number: 4
ISSN: 1318-0010
Volume: 26
Year: 1992
Pages: from 329 to 331
Number of references: 5
Language: engleski
Summary: The paper presents results of the analysis of the influence
ofthe working intensity and isolation maintenance frequencyincrease on the
example of a pusher-type furnace in a strip andbilet rolling mill. The
results obtained analytically show thatthe specific heat energy consumption
decreases for about 18 % ifthe intensity of the pusher-type furnace
increases 1,81 times.The results obtained analysing operating data of the
furnace workdo not show significant deviations from the results
obtainedanalytically. The same way, the increase of the
isolationmaintenance frequency and that of the layers removal from thefloor
to the half of the period would decrease the averagespecific heat energy
consumption for about 10 %.
Keywords: Pusher-type furnace, Productivity, Isolation, Energy, Consumption
- Type of paper
: Paper in journal
Title: UHP - furnaces for steel
- Authors:
- Kundak, Mijo (24642)
Journal: Hrvatsko gospodarstvo
Number: 35
ISSN: 0000-0000
Volume: 2
Year: 1992
Pages: from 11 to 12
Language: hrvatski
Summary: This paper gives a survey of the steel production economy
in thedifferent electric-furnaces.
Keywords: Economy, Electric-Furnace
- Type of paper
: Paper in journal
Title: A Brief Presentation of the Development of Iron Production
Procedures
- Authors:
- Črnko, Josip (57413)
Journal: Metalurgija
Number: 3
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 117 to 121
Number of references: 16
Language: hrvatski
Summary: The paper briefy describes the procedures of iron
productiondating back at least two thousand year BC. All the
procedurescounted up have not taken a constant place in iron production,but
they have influenced the development of a blast furnaceprocedure. Modern
blas furnaces, reaching the volume of 5580 m3,remain the aggregates which
in the best way answer to theconditions of pig iron production.
Keywords: Pig iron, Procedures of production, Development and description
- Type of paper
: Paper in journal
Title: The steel production economy by the converter and electric
arc furnace procedure
- Authors:
- Kundak, Mijo (24642)
Journal: Metalurgija
Number: 3
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 93 to 96
Number of references: 21
Language: hrvatski
Summary: This paper gives a survey of the steel production economy
by theconverter-and electric arc procedure. The greatest portion in
thecosts of the steel production in the electric arc furnaces isenergy-and
electrodes consumption. The energy portion in thesteel production by the
converter procedure is insignificant. Theproduction cost in the converters
is considerable lower relatedto the production cost in the electric
furnace. Comparing thesteel price of electric-and converter procedure, the
charge costsare found to be the most important factores.
Keywords: Economy, Production, Steel, Convertor, Electric procedure
- Type of paper
: Paper in journal
Title: Contribution to the methodics of the thermotechnical value
of natural gas combustion analysis in sectional furnaces
- Authors:
- Črnko, Josip (57413)
- Kundak, Mijo (24642)
Journal: Goriva i maziva
Number: 2
ISSN: 0350-350X
Volume: 32
Year: 1993
Pages: from 79 to 95
Number of references: 5
Language: hrvatski
Summary: The paper presents the methodics of the thermotechnical
value ofnatural gas conbustion analysis in terms of air deficiencyrelated
to the air theoretically necessary. A verification of themethodics of
analysis was carried out in SELAS type sectionalfurnaces of Sisak Ironworks
seamless tube rolling mill. By thisanalysis it was found out that during
investigations the zonalfactor of air in the sectional furnaces was in the
range of 0,83- 0,93. A composition of the incomplete combustion products
wasalso found out, as well as a share of unused chemically tied heatbeing
in the range of 9,00 - 22,02 %. Calculations showed thatthe natural gas
combustion at minimum air excess necessary colddecrease its consumption for
12,07 %.
Keywords: Gas fuels, Incomplete combustion, Methodics of analysis andcalculation, Sectional furnaces
- Type of paper
: Paper in journal
Title: Numerical simulation of the heat balance influence on the
cast refining in the steel production
- Authors:
- Kundak, Mijo (24642)
- Črnko, Josip (57413)
Journal: Metalurgija
Number: 1
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 23 to 26
Number of references: 8
Language: hrvatski
Summary: This paper presents the numerical simulation results of
thevalues changes influence of some heat balance items on the castrefining
in the steel production process with an example of theopen-hearth furnace.
The stated perceptions, obtained on thebasis of the test results, make it
possible to decide on theoxygen bloeing into the cast, knowing the carbon
content and heattemperature immediately before the start of refining. At
the andare compared some values obtained by the numerical simulation
andthose obtained by measuring in the concrete plant conditions.
Keywords: Steel productions, Cast refining, Heat balance, Numerical simulation
- Type of paper
: Paper in journal
Title: How to cheaper steel
- Authors:
- Kundak, Mijo (24642)
Journal: Hrvatsko gospodarstvo
Number: 54
ISSN: 0000-0000
Volume: 3
Year: 1993
Pages: from 28 to 29
Language: hrvatski
Summary: Comparing the steel production price of open-hearth
andantiquated electric procedure in the Sisak Iron Work has beengiven in
this article.
The production cost in the open-hearth furnaces is considerablelower
related to the production in the electric furnace.
Keywords: Production cost, Open-hearth procedure, Electric procedure
- Type of paper
: Paper in journal
Title: Effect of hydrogen on the stress corrosion behaviour of
medium carbon Mn/Mn-V steel
- Authors:
- Malina, Jadranka (83026)
- Gojić, Mirko (63390)
- Malina, Marijan (92381)
Journal: Transaction of the Technical University of Kosice
Number: 2
ISSN: 0960-6076
Volume: 2
Year: 1992
Pages: from 185 to 193
Number of references: 13
Language: engleski
Summary: Susceptibility to hydrogen embrittlement (HE) of tubing
fromcommercial medium carbon Mn steel, as well as of experimental lowalloy
Mn-V steel was exmained. Cathodic charging with hydrogenrevealed that by
heat treatment of tubing better resistivity toHE is achieved. Fractographic
analysis of stepwise cracking fromsolution saturated with H2S has shown the
considerable role ofMnS inclusions in microstructure: they are trap-sites
forhydrogen accumulation.
Keywords: Mn/Mn-V low alloy steel, Hydrogen embrittlement, Stepwise cracking
- Type of paper
: Paper in journal
Title: Application of Mossbauer's spectroscopy to metallurgy
- Authors:
- Ivanušić, Vera (63094)
Journal: Metalurgija
Number: 3
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 101 to 104
Number of references: 18
Language: hrvatski
Summary: This paper gives a survey of some possibilities for
applicationof Mossbauer's spectroscopy to metallurgy. It
considersmetallurgical system as well as those systems which are more
andmore important for the manufacture of new materials.
Keywords: Metallurgy, Mossbauer spectroscopy
- Type of paper
: Paper in journal
Title: Investigation of Pipe Steel Flow Stress and Limit
Deformability by Means of Hot and/or Cold Tensile Test
- Authors:
- Golja, Marijan (57764)
- Mamuzić, Ilija (27862)
Journal: Zavarivanje
Number: 4
ISSN: 0562-1887
Volume: 34
Year: 1992
Pages: from 31 to 36
Number of references: 12
Language: hrvatski
Summary: This paper deals with the problems of flow stress and
limitdeformability investigation at elevated temperatures. Our
owninvestigation results of carbon and low-alloyed structural
steelsobtained by hot torsion test in temperature range from 1073 to1473 K
as well as by cold tensile test have been presented.
Keywords: Flow steress, Hot torsion test, Limit deformability, Pipe steel
- Type of paper
: Paper in journal
Title: Contribution to the Research of the Residual Elements
Influence on the Steel Plasticity
- Authors:
- Mamuzić, Ilija (27862)
- Golja, Marijan (57764)
- Križanić, Rade (23663)
Journal: Metalurgija
Number: 4
ISSN: 0543-5846
Volume: 30
Year: 1991
Pages: from 131 to 135
Number of references: 10
Language: hrvatski
Summary: The work presents a short theoretical review of the
residualelement influence on the steel plasticity and gives thecomparison
of the relations of the allawed residual elementquantities in steel, given
in the world literature. Our research,carried out by tensile test and
torsion test methods in thetemperature range 800-1250řC, proved that
residuals had a badinfluence on the plasticity and yield stress, of the
castingstructure, depending on ingot size and the influence was moreobvious
on deformad structure.
Keywords: Residual Elements, Steel Plasticity, Deformed Structure, Casting Structure
- Type of paper
: Paper in journal
Title: Properties Analysis of the St 52-3 Grade Steel After
Thermo-Mechanical Treatment
- Authors:
- Buršak, Marjan
- Michel, Jozef
- Mamuzić, Ilija (27862)
Journal: Metalurgija
Number: 4
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 135 to 140
Number of references: 6
Language: engleski
Summary: In the present paper the mechanical properties and the
resistanceto brittle fracture are analyzed for a thermo-mechanicallytreated
St 52-3 grade steel. These properties were invwestigatedon three thickness
variants. Considering substructure theparticular reinforcement
contributions are analyzed. The aim ofthis paper is too, the verification
of the validity ofcorrelations derived for mixed structures.
Keywords: Properties of steel, Thermo-mechanical treatmen, Correlation, Structure
- Type of paper
: Paper in journal
Title: Deformation Features of Highstrength Bainit Steel
- Authors:
- Križanić, Rade (23663)
- Hensel, Arno
- Mamuzić, Ilija (27862)
- Nikolić, Đurđica
Journal: Metalurgija
Number: 3
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 69 to 75
Number of references: 10
Language: njemački
Summary: The paper deals with investigation of deformation values
ofhighstrength bainit steel; deformation resistence, criticaldeformation
and deformation up to the fracture depending ontesting temperature,
deformation speed and deformations.Investigations are performed on torsion
plastometers. Equationsare derived as dependance of deformation features on
influencingparameters.
Keywords: Deformation resistance, Deformation speed, Torsion plastometer
- Type of paper
: Paper in journal
Title: Determination of Tensile Stress for Cold Drawing of Steel
Pipes
- Authors:
- Iharoš, Berislav (16913)
- Mamuzić, Ilija (27862)
Journal: Metalurgija
Number: 4
ISSN: 0543-5846
Volume: 30
Year: 1991
Pages: from 137 to 141
Number of references: 11
Language: hrvatski
Summary: The cold flow line was determined for three grades of steel
pipeČ.1212, Č.3100 and Č.1402 by the tensile test method with anundeformed
sample (by M. Rheile). Tensile stress for steel pipecold drawing without a
plug, with a floating plug and with a longplug was measured by a extension
belt measuring transducer. Onthe basis of the test results tensile stress
analyticalexpression were determined for each grade of steel and each
steelpipe cold drawing method. The analytical expression are simpleand
easily applicable and their results are within satisfactorylimits for a
production plant.
Keywords: Tensile Stress, Cold Drawing, Steel Pipe
- Type of paper
: Paper in journal
Title: Stress Decrease Possibility in Tubes - Logarithmic Roll
Pas Design
- Authors:
- Kostelac, Marko (79305)
- Iharoš, Berislav (16913)
Journal: Metalurgija
Number: 4
ISSN: 0543-5846
Volume: 30
Year: 1991
Pages: from 143 to 147
Number of references: 13
Language: hrvatski
Summary: This paper presents a possibility for lower residual
stresses ofcold roll tubes by the new roll pass design. The logarithmic
rollpass design is specified in detail, analysed by distribution
ofindividual true strain in the working section and compared
withMannesmann's.
Keywords: Stress Decrease, Tubes, Logarithmic Roll Pass Design.
- Type of paper
: Paper in journal
Title: Supplement to the Investigation of Two-Phase ŕ+á Titanium
Alloys
- Authors:
- Billy, Jozef
- Mamuzić, Ilija (27862)
Journal: Metalurgija
Number: 2
ISSN: 0543-5846
Volume: 31
Year: 1992
Pages: from 49 to 52
Number of references: 9
Language: engleski
Summary: The article presents a brief survey of two-phase titanium
alloysand the reason for the presence of non-homogenous structures inafter
deformation by pressing and forging. On the basis ofinvestigations two
reasons were ascertained for the formation oflocalized deformation bands.
The firs reason is the occurence ofcooler and relatively rigid zones of
conical shape and second andmore frequent reason is the localized adiabatic
heating.
Keywords: Two-phase titanium alloys, Deformation by pressing and forging, Localized deformation bands.
- Type of paper
: Paper in journal
Title: Determination of Deformation Resistance of High-Strength
Weldable Construction Steel with Bainitic Structure
- Authors:
- Križanić, Rade (23663)
- Mamuzić, Ilija (27862)
- Nikolić, Đurđica
Journal: Metalurgija
Number: 2
ISSN: 0543-5846
Volume: 31
Year: 1992
Pages: from 61 to 66
Number of references: 10
Language: hrvatski
Summary: The investigation includes determination of
deformationresistance of bainitic structure steel on the basis of
theexperimened torsion moment, i.e. hardening coefficient m and m.It was
proved that the change of the coefficient m value occursin the range from
0.037 to 0.224. The average value of the mcoefficient, dependent on the
austenitization temperature is inthe range from 0.080 to 0.150.Deformation
resistance can bedetermined knowing these coefficient values and torsion
moment,obtained by experiments based upon data from the literature.
Keywords: Deformation Resistance, Bainitic Steel, Hardening Coefficient
- Type of paper
: Paper in journal
Title: Standard Technology Procedure for Cold Drawing of Steel
Tubes
- Authors:
- Iharoš, Berislav (16913)
Journal: TEHNIKA - Rudarstvo, geologija i metalurgija
Number: 1
ISSN: 1318-0010
Volume: 26
Year: 1992
Pages: from 97 to 99
Language: hrvatski
Summary: The standard technology procedure for the cold drawing
process ofsteel tubes, different dimensions, quality and delivericondition,
was made on computer. This software make possiblechoise for the optimal
program of drawing process and dimensionof tools, planning and conducting
of production.
Keywords: Cold Drawing, Steel Tubes, Software.
- Type of paper
: Paper in journal
Title: Structural Changes in Low-Carbon Steels During
Thermomechanical Treatment
- Authors:
- Miranova, Olga
- Drujan, Vladimir
- Mamuzić, Ilija (27862)
Journal: Metalurgija
Number: 1
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 7 to 15
Number of references: 11
Language: hrvatski
Summary: The new way of thermomechanical treatment (TMT) has
beeninvestigated in order to ensure the high value mechanicalproperties of
the finished cold deformed low-carbon steel tubes.During introduction of
the TMT dynamic deformation procedure(bending in the plasticity area,
number of cycles to 30) anessential change occurs in the steel structure
and thereby itbecomes uniform.
Keywords: Low-Carbon steel, Thermomechanical treatment, Mechanical properties, Dynamic deformation.
- Type of paper
: Paper in journal
Title: Application of Expert Systems in Production of Tubes by
Cold Working
- Authors:
- Mamuzić, Ilija (27862)
- Garan, Vjačeslav
- Drujan, Vladimir
Journal: Transaction of the Technical University of Kosice
Number: 2
ISSN: 0960-6076
Volume: 2
Year: 1992
Pages: from 179 to 184
Number of references: 12
Language: engleski
Summary: Problems of creation and application of expert systems on
theexamples of automatizing cold-worked tube productiontechnological
process designing are considered in this study. Anexpert system is capable
to model new decision accptancealgorithms by means of knowledge base
replenishment withtechnology, deformation theory, equipment and decision
choicemethods data which help to optimise production.
Keywords: Expers Sistems, Cold-Worked Tube, Knowledge Base
- Type of paper
: Paper in journal
Title: Optical Modelling of Non-Symmetric Rolling Process
- Authors:
- Šlomčak, Georg
- Mamuzić, Ilija (27862)
Journal: Metalurgija
Number: 3
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 77 to 80
Number of references: 9
Language: hrvatski
Summary: This article gives modelling results of non-symmetric
striprolling between the rolls and the plane groand with adjustment
ofvarious rates and lubrication conditions.
Keywords: Optical Modelling, Rolling Process, Strip, Varions rates
- Type of paper
: Paper in journal
Title: Thermal Fatigue of Cast Steels
- Authors:
- Mamuzić, Ilija (27862)
Journal: Ljevarstvo
Number: 2
ISSN: 0024-5402
Volume: 35
Year: 1993
Pages: from 107 to 111
Number of references: 10
Language: hrvatski
Summary: Thermal fatigue of cast steels, Carbon and vanadium
microalloyedwas investigated by comparison of the number of heat exchenges
upto destruction in intervals 873-373K, 873-473K and 873-573 K. Thetime up
to the starting of the samples destruction at dynamicloading of 100 MPa at
temperatures 873 and 973 K as well as themicrostructure was determined. It
was proved that vanadiummicroalloying prolog the life of the samples on
account of theferrite deformation and the use of these steels for the
dynamicloaded parts at higher temperatures is more reliable.
Keywords: Cast steel, Thermal fatigue, Mechanical properties, Microstructure
- Type of paper
: Paper in journal
Title: The Rheological Model of Deformation Nidus in the Process
of Rolling
- Authors:
- Šlomčak, Georg
- Mamuzić, Ilija (27862)
- Vodopivec, Franc
Journal: TEHNIKA - Rudarstvo, geologija i metalurgija
Number: 4
ISSN: 1018-0010
Volume: 27
Year: 1993
Pages: from 335 to 341
Number of references: 10
Language: engleski
Summary: On the base of contemporary ideas of metal preeure shaping
theoryand investigation results of metal stress-strained state
duringrolling using variation principles of mechanics, authors studiesof
metals and alloys plastometric classification, aspectdevelopment of a new
model of high deformation nidus -reological,are biven in this study. The
model makes it possible to explainregularities in plastic deformation
intensity distribution innon-contact zones as well as conditions of front
end deformationdepending on plastometric properties of metals.
Confirmingexperimental data and mew regularities of metal
deformationdevelopment before input of feed into the rolls and the
outputare also given in this study.
Keywords: Stress-strained state, Model reological, Deformation, Non-contact zones
- Type of paper
: Paper in journal
Title: Modeling of Plastic Metal Processing
- Authors:
- Mamuzić, Ilija (27862)
- Turk, Radomir
- Balakin, Vladimir
Journal: Metalurgija
Number: 1
ISSN: 0543-5846
Volume: 31
Year: 1992
Pages: from 15 to 20
Number of references: 18
Language: hrvatski
Summary: This paper bives a review of physical modelling. The
procedure ofhollow semi-product "cup" (one phase at seamless pipes
productionby Calmes) was examined by similarity theory in
laboratoryconditions and the real material flow was determined.Mathematical
modelling shows a number of stages which begin withthe problem definition
of the subject and end with the resultanalysis and recommendations for
implementation. The example ofhot rolling of compound wide strips (base
construction steel,addition Cr-Ni steel) was used for optimization of the
striprolling schedule applying the complex mathematical modelling.
Keywords: Physical modelling, Hollow shell, Material flow, Mathematical modelling, Rolling schedule
- Type of paper
: Paper in journal
Title: Formation of Knowledge Based of Expert Systems for Applied
Problems in Ferrous Metallurgy
- Authors:
- Drujan, Vladimir
- Garan, Vjačeslav
- Mamuzić, Ilija (27862)
Journal: Metalurgija
Number: 1
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 27 to 30
Number of references: 4
Language: engleski
Summary: The article deals with the experience in the formation and
use ofknowledge bases of expert systems such as an expert system
forcomputer-aided design of cold-worked tubes production. Problemsof
knowledge base structure and methods of its forming havebeendoscussed.
Keywords: Expert systems, Knowledge Base, Ferrous Metallurgy
- Type of paper
: Paper in journal
Title: Expert Systems and their Application to Metallurgy
- Authors:
- Garan, Vjačeslav
- Drujan, Vladimir
- Mamuzić, Ilija (27862)
Journal: Metalurgija
Number: 4
ISSN: 0543-5846
Volume: 31
Year: 1992
Pages: from 125 to 130
Number of references: 12
Language: hrvatski
Summary: Besides the basis of the expert system, the application to
thecold working of tubes is analysed. It is possible to optimize theprocess
of cold working of tubes, based upon more influentialfactors, tube sizes,
material quality, types of cold workingprocedures, deformation grade and
capacity.
Keywords: Expert Systems, application to Metallurgy, Optimize the process
- Type of paper
: Paper in journal
Title: Metal Products to Oil- and Petrochemical Equipments
- Authors:
- Mamuzić, Ilija (27862)
Journal: Metalurgija
Number: 1
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 31 to 35
Number of references: 20
Language: hrvatski
Summary: The demands for the metal products and tendencies
intechnological procedures development have been described. Thelatest
achievements in the combination of two or more processdegrees of quite
different characters have been stated. the stateand development of steel
tubes (seamless and welded) in the worldand the required tubes properties
and grades are particularlypresented. The tubes production procedures are
described, too.
Keywords: Metal products, Oil and Petochemical Equipment, State and development, tubes properties
- Type of paper
: Paper in journal
Title: Directions for Research and Technology of the Plastic
Metal and Alloy Forming
- Authors:
- Mamuzić, Ilija (27862)
- Turk, Radomir
Journal: Metalurgija
Number: 4
ISSN: 0543-5846
Volume: 32
Year: 1993
Pages: from 167 to 176
Number of references: 15
Language: hrvatski
Summary: This paper presents the directions for the research at
theplastic metal and alloy forming, i.e. simulation methods ofresearch.
That refers to the interactionn of the researchsystems, as physical
modelling and simulation as well as computercontrolled simulation related
to the material, forming procedureand application. These directions of
plastic forming technologyemphasize the combination of two or more process
stages of quitedifferent character. They are also acknowledged in
thedevelopment of the technologies of CPS (Compact StripProduction), ISP
(Inline Strip Production) and CPR (Casting,Pressing, Rolling).
Keywords: Directions for Research, Technology of the Plastic Forming, Simulation methods, Development of the Technologie
- Type of paper
: Paper in journal
Title: Contribution to the investigations of introducing
automatic control of the process of fuel and getting out of cast combustion
in steel production
- Authors:
- Kundak, Mijo (24642)
- Črnko, Josip (57413)
Journal: Goriva i maziva
Number: 3
ISSN: 0350-350X
Volume: 33
Year: 1994
Pages: from 151 to 163
Number of references: 10
Language: hrvatski
Summary: The paper sets the reaction chamber energy balance of an
open-herth furnace that enables the analysis of the furnace capacity
influence upon the energy brought by fuel during cast rafining in the
course of steel production. Based on the speed of decarbonization,
calculations of certain parameters and energy balance, a necessary heavy
fuel oil consumption and the air excess coefficient for its combustion are
definid. Adequately adapted energy balance can be applied in final
processing of steel in a melting pot (pot metallurgy).
Keywords: Liquid fuel, Energy balance, Fuel saving, Open-hearth furnace
- Type of paper
: Paper in journal
Title: Influence of the scaling upon the heating process of steel
slabs in a pusher-type furnace
- Authors:
- Kundak, Mijo (24642)
- Črnko, Josip (57413)
Journal: Yournal of Materials Processing Technology
Number: 4
ISSN: 1318-0010
Volume: 28
Year: 1994
Pages: from 619 to 622
Number of references: 9
Language: engleski
Summary: In the frame of the paper an existing and a proposed more
optimal temperature regime for heating of steel slabs in a pusher-type
furnace is analysed. The influence of steel oxidation upon the heating
process and its influence upon the optimal temperature regime calculation
is also investigated.
Keywords: Pusher-type furnace, Heating of steel, Scaling
- Type of paper
: Paper in journal
Title: A short presentation of investigations in connection with
red mud processing in Croatia
- Authors:
- Črnko, Josip (57413)
Journal: Metalurgija
Number: 4
ISSN: 0543-5846
Volume: 33
Year: 1994
Pages: from 167 to 169
Number of references: 21
Language: engleski
Summary: The paper gives a short presentation of investigations in
Croatia, from the red mud smelting in an electric arc furnace to the
combined processing, for the period between 1945. and 1985. It ends with
recomendations for its cheaper processing.
Keywords: Red mud, Combined processing, Recomendations
- Type of paper
: Paper in journal
Title: Application of Niobium Microalloyed Steel in Production of
Thin Scaffold Tubes
- Authors:
- Rešković, Stoja (57806)
- Preloščan, Andrija (38695)
- Novosel-Radović, Vjera (33706)
- Fried, Željko
Journal: Metalurgija
Number: 2
ISSN: 0543-5846
Volume: 33
Year: 1994
Pages: from 70 to 83
Number of references: 21
Language: hrvatski
Summary: The paper presents the research results of niobium
microalloyed steel application in production of hot rolled strips for
welded tubes for scaffold construction. The effect of rolling parameters on
tubes quality was investigated. On the basis of the tubes properties the
possibility of wall thickness reduction was investigated. The obtained
results showed that beside the significant wall thickness reduction high
quality of hot rolled welded scaffold tubes can be achieved.
Keywords: Niobium Microalloyed steel, Production of Thin scaffold Tubes, Rolling parameters
- Type of paper
: Paper in journal
Title: Fractionting N-determination in the Steel by means of a
Carrier Gas Method
- Authors:
- Preloščan, Mira
- Merle, Vesna
- Preloščan, Andrija (38695)
Journal: Metalurgija
Number: 1/2
ISSN: 0543-5846
Volume: 34
Year: 1995
Pages: from 25 to 29
Number of references: 18
Language: hrvatski
Summary: Steels with the different contents of nitrogen were
analysed by hot extraction process with helium as gas carrier. For this
purpose was used an automatic device LECO-TC 436 for nitrogen and oxygen
determination which are contained in metals, ores and other materials.
Nitrogen releases from the particular nitrides at the different
temperatures and crosses the cell for the thermal conductivitz measuring.
The response abtained transfers through the calculator at the printer which
automatically writes down the results of the analysis in the time up to 210
s.
Keywords: Fractionting N-determination, Hot extraction, Carrier Gas Method, Thermal conductivity measuring
- Type of paper
: Paper in journal
Title: Influence of plastic steel deformation on energy
consumption
- Authors:
- Kundak, Mijo (24642)
- Križanić, Rade (23663)
- Nikolić, Đurđica
- Acs, Željko
Journal: Energetika gospodarstvo ekologija
Number: 8
ISSN: 1330-0628
Volume: 2
Year: 1994
Pages: from 48 to 50
Number of references: 11
Language: hrvatski
Summary: The paper gives a survey of the contribution to the
reduction of energy consumption by increasing the speed of steel
deformation into strips and possible increase of capacity as well as the
reduction of rolling scale achieved by a lower number of pass reductions
and rolling stands in continuons mill in Željazara Sisak.
Keywords: Optimization, energy consumption, plastic deformation
- Type of paper
: Paper in journal
Title: Development based on the Science
- Authors:
- Kundak, Mijo (24642)
Journal: Hrvatsko gospodarstvo
Number: 66
Volume: 4
Year: 1994
Pages: from 54 to 56
Language: hrvatski
Summary: The paper summarites the faults in development of steel
manufacturing industry in Croatia as well as the possibility of future
existance.
Keywords: development, Steel production in Croatia, existance
- Type of paper
: Paper in journal
Title: The Influence of Raw Materials and Technological
Conditions on the Carbon Content in Blast Furnace Foundry Pig Iron
- Authors:
- Boras, Ivica
- Markotić, Anto (57483)
- Šimunović, Ivana (83004)
Journal: Metalurgija
Number: 3
ISSN: 0543-5846
Volume: 34
Year: 1995
Pages: from 107 to 111
Number of references: 6
Language: hrvatski
Summary: It is researched the dependence of foundry pig iron carbon
content on the determination of raw materials and technological conditions
of blast furnace production. The established dependences and correlations
showed on the dominantly influence of temperature blowing air and the
silicium content of iron.
Keywords: carbon, foundry pig iron, blast furnace, raw materials, technological conditions.
- Type of paper
: Paper in journal
Title: Rheological Similarity of Metals and Alloys
- Authors:
- Šlomčak, Georg
- Mamuzić, Ilija (27862)
- Vodopivec, Franc
Journal: Yournal of Materials Processing Technology
ISSN: 1318-0010
Volume: 40
Year: 1994
Pages: from 315 to 325
Number of references: 10
Language: engleski
Summary: A rheological model of metals and alloys with a minimized
number of parameters has been developed which makes possible the describing
of complex experimental dependencies. A system of rheological similarity
criteria has been obtained which helps to select materials and models for
the physical simulation of plastic deformation processes and to ascertain
the similarity between metals and alloys for their rheological grouping.
Keywords: Rheological model, experimental dependency, physical simulation of plastic deformation processes
- Type of paper
: Paper in journal
Title: Lead as a Rheological Model for Investigating Hot Rolling
Processes
- Authors:
- Šlomčak, Georg
- Mamuzić, Ilija (27862)
- Vodopivec, Franc
Journal: Transaction of the Technical University of Kosice
Number: 4
ISSN: 0960-6076
Volume: 3
Year: 1993
Pages: from 331 to 335
Language: engleski
Summary: Lead and its alloys are the most suitable materials for the
rheological modelling of hot rolling processes. With small additions of
tellurium it is possible to change significantly the rheological properties
of lead, a fact important for the maintenance of several similarity
conditions. The importance of the properties of material on the kinematics
of the deformed metal is demonstrated by means of process modelling of
thick strip rolling.
Keywords: Rheological properties of lead, properties of material, thick strip rolling
- Type of paper
: Paper in journal
Title: The Expert Systems in Ecology of Metallurgy
- Authors:
- Mamuzić, Ilija (27862)
- Garan, Vjačeslav
- Drujan, Vladimir
Journal: Hutnicke listy
Number: 6
ISSN: 0018-8069
Volume: 39
Year: 1994
Pages: from 5 to 7
Number of references: 8
Language: engleski
Summary: Besides the paper on which the expert system is built, the
aim of the papers is to create the automatized programme-technical
observation ecological continuous system of formation and prediction of
gaseous dust consequences in technological aggregate of metallurgical
plants. This influence is observed inall stages of metallurgical cycle,
including projection, pilog plant, exploration, updating and
reconstruction. There are used adapted mathematical models.
Keywords: Ecology, expert system, automatized programme, mathematical model
- Type of paper
: Paper in journal
Title: The Role of Contact Friction and Rheology in the
Deformation at Plastometric Tests of Rheologically Complex Materials
- Authors:
- Šlomčak, Georg
- Mamuzić, Ilija (27862)
- Vodopivec, Franc
Journal: Yournal of Materials Processing Technology
Number: 4
ISSN: 1318-0010
Volume: 28
Year: 1994
Pages: from 579 to 582
Number of references: 10
Language: engleski
Summary: The deformation anomalies of higher orders at plastometric
tests are studied on easily deformable lead alloys-models of different
rheological complexity by original testing methods. It is ascertained that
the development of deformation anomalies depends upon the degree of
rheological complexity of the material. Simple strain anomalies are due to
the inadequate conditions of contact friction, while those of the highere
orders results mainly from microrelief of the sample butts. Recommendations
for the obtention of homogeneity of deformation at plastometric tests are
given. The testsshow that the deformation of rheologically complex metals
develops according to laws basically different of the contemporary notions
of the mechanics of plastics deformation.
Keywords: Plastic deformation, rheology, deformation anomalies, contact friction, homogeneous deformation, plastometric tests, rheologically complex materials.
- Type of paper
: Paper in journal
Title: Deformation Anomalies of Higher Order during the Plastic
Extention of Rheologically Complex Materials
- Authors:
- Šlomčak, Georg
- Mamuzić, Ilija (27862)
- Vodopivec, Franc
Journal: Yournal of Materials Processing Technology
Number: 4
ISSN: 1318-0010
Volume: 28
Year: 1994
Pages: from 583 to 587
Number of references: 10
Language: engleski
Summary: New deformation anomalies of rheologically complex
materials were discovered and demonstrated. It was found out that in the
process of axial extention during the decrease of resistance to deformation
secondary deformation heterogeneities take place alternated with
deformation homogenities due to changes in resistance to deformation.
Keywords: Rheology, tensile test, deformation anomalies, heterogeneity, plastic extention
- Type of paper
: Paper in journal
Title: Structure and Properties of Stripped Microalloyed Steel
with Yield Stress over 620 MPa
- Authors:
- Šimon, Arpad
- Mamuzić, Ilija (27862)
Journal: Metallurgy and new Materials researches
Number: 1/2
Volume: 2
Year: 1994
Pages: from 80 to 86
Number of references: 12
Language: engleski
Summary: The fine grained accicular structures are the guarantee of
required over 620 MPa yield stress of microalloyed by rolling on hot wide
strip mills. The fine grained accicular ferrite or bainite structures
ofmicroalloyed steels could be achieved by means of controlled rolling
process or with colute additions of Mn, Mo, Nb, Ti and B either. In the
present paper the microalloyed steels, with corresponding yield stress 700
MPa and with required transition temperature up to -20řC, structure,
strength properties, and fracture properties relationships are studied.
Keywords: Microalloyed steel, controlled rolling process, yield stress, structure
- Type of paper
: Paper in journal
Title: Structure and properties of the Metal of Tubes Produced
from Centrifugally Vacuum Cast Austenitic Stainless Steel Billets
- Authors:
- Lezinskaja, Jarmina
- Mamuzić, Ilija (27862)
- Parilak, Ladislav
- Vodopivec, Franc
Journal: Kovovy materiali
Number: 6
Volume: 6
Year: 1994
Pages: from 517 to 521
Number of references: 8
Language: engleski
Summary: Comparative analysis of the structure and properties of the
metal of cold-finished extra-thin wall tubes manufactured from billets
centrifugally cast in vacuum and from billets obtained by the conventional
two-stage process including vacuum induction melting and vacuum refining
has been carried out. It is shown that structure and properties of
cold-finished tubes made from vacuum-centrifugally cast billets are not
inferior to those of tubes from conventional billets; however, vacuum
centrifugal casting of tube billets ensures a lower content of non-metallic
inclucions in tube metal along with lower metal and labour consumption.
Keywords: Structure and properties, austenitic stainless stell, cast billet
- Type of paper
: Paper in journal
Title: Relations between Criteria Describing Resistance to
Brittle Fracture and their Utilization for Evaluation Micro-alloyed Steels
- Authors:
- Michel, Jozef
- Mamuzić, Ilija (27862)
- Buršak, Marjan
Journal: Metallurgy and new Materials researches
Number: 4
Volume: 2
Year: 1994
Pages: from 11 to 22
Number of references: 10
Language: engleski
Summary: The article has shown the relations between criteria
describing resistance to brittle fracture considering the veriety of
experimental results obtained (using Charpy impact testing, DWTT, DWT and
plain stain fracture toughness tests). It describes and discusses the
requested and certified criteria used in material standard to express the
resistance to brittle fracture, recomend changes and new methods to
evaluate more precisely the resistance to brittle fracture in these steels.
Keywords: Resistance to brittle fracture, microalloyed steel, new methods
- Type of paper
: Paper in journal
Title: Contribution to Investigation of Three-Dimensional Flow of
Materials and Deformation in Hollow Shell Crossrolling
- Authors:
- Golja, Marijan (57764)
- Mamuzić, Ilija (27862)
- Fridrih, Hrvoje
Journal: Metalurgija
Number: 1
ISSN: 0543-5846
Volume: 33
Year: 1994
Pages: from 19 to 22
Number of references: 10
Language: hrvatski
Summary: The behaviour of metals during hot plastic deformation,
especially during crossrolling in the production of seamless steel tubes is
investigated both theoretically and experimentally. Material flow during
crossrolling and unequality of layer deformation are presented together
with the analytical results of experiments undertaken.
Keywords: The cross rolling, the seampless tube, the flow of Materials
- Type of paper
: Paper in journal
Title: Microstructure and Properties of microalloyed Steel Sheer
with Yield Strength exceeding 620 MPa
- Authors:
- Šimon, Arpad
- Mamuzić, Ilija (27862)
Journal: Metalurgija
Number: 4
ISSN: 0543-5846
Volume: 33
Year: 1994
Pages: from 137 to 140
Number of references: 8
Language: engleski
Summary: The microstructure, mechanical properties and resistance to
brittle fracture as wel as the correlation among them are given in the
presented work for the grade KODUR E 700 TS microalloyed steel produced in
East Slovakian iron Works Košice. The chemical composition (Mn, Mo, Nb, Ti
and B) in connection with the technology of controlled cooling of the 10 mm
sheet produce a fine acicular ferrite or bainite microstructures, a yield
strength exceeding 700 MPa a transition temperatures lower than -20řC.
Keywords: The microstructure, the properties, the microalloyed steel
- Type of paper
: Paper in journal
Title: Contribution to designing of the mould for rolls Casting
- Authors:
- Mamuzić, Ilija (27862)
- Gorjanoj, Vjačeslav
Journal: Ljevarstvo
Number: 2
ISSN: 0024-5402
Volume: 36
Year: 1994
Pages: from 37 to 40
Number of references: 9
Language: hrvatski
Summary: The paper presents the new mould constructions for the
rolls casting that are used at the universal rolling mills of beams. The
appropriate working layer as well as the side walls of the rolls are
obtained on the basis of the proper choice of the mass ratio for some mould
elements and the coolingsurfaces by the optimal arrangement of the radial
degassing channels. This construction has a series of advanteges
particulary for the rolls quality and reduction of the production costs.
Keywords: Rolss casting, mould construction, Working layer, quality
- Type of paper
: Paper in journal
Title: Mathematical Model of Sectional Furnace
- Authors:
- Lazić, Ladislav (105552)
Journal: Metalurgija
Number: 2
ISSN: 0543-5846
Volume: 33
Year: 1994
Pages: from 73 to 78
Number of references: 8
Language: hrvatski
Summary: In this paper the mathematical model of a sectional rolling
mill high-speed tube heating furnace is presented. The objective of the
described model is to define optimum furnace heating parameters for a
specific productivity by simulating a heating process.
Keywords: Mathematical model, sectional furnace, heating process, optimum parameters.
- Type of paper
: Paper in journal
Title: New Designes of Impulse Burners
- Authors:
- Lazić, Ladislav (105552)
- Horbaj, Peter
Journal: Metalurgija
Number: 4
ISSN: 0543-5846
Volume: 33
Year: 1994
Pages: from 151 to 154
Number of references: 7
Language: hrvatski
Summary: A short description of general characteristics of impulse
burners and desing features of five outside-mixing and inside mixing
(premixing) impulse burners designed at the HF TU Košice are presented.
Keywords: Impulse burner, mixing, premixing.
- Type of paper
: Paper in journal
Title: Mathematical Model of Biomass Pyrolysis
- Authors:
- Horbaj, Peter
- Lazić, Ladislav (105552)
Journal: Metalurgija
Number: 3
ISSN: 0543-5846
Volume: 34
Year: 1995
Pages: from 79 to 83
Number of references: 7
Language: engleski
Summary: In this paper the mathematical model of heat transfer and
the kinetics of pyrolysis of biomass at lower temperatures is presented.
The model serves for determination of surface and core temperature, and
density of observed solid particle as well as time of thermal decomposition
of biomass and can be used for the improvement of the charcoal-making
procedure.
Keywords: Mathematical model, biomass pyrolysis, charcoal, temperature distribution, density, time, thermal decomposition.
- Type of paper
: Paper in journal
Title: The Parametars Influence on the Value of K(Mn,Si) and
K(Si,S) Constants in the Production of Foundry Pig Iron
- Authors:
- Boras, Ivica
- Markotić, Anto (57483)
Journal: Metalurgija
Number: 2
ISSN: 0543-5846
Volume: 33
Year: 1994
Pages: from 59 to 65
Number of references: 6
Language: hrvatski
Summary: The influence of Si on the final distribution of Mn and S
between iron and slag has been investigated by the observation of reactions
expressed by K(Mn,Si) and K(Si,S) constants. In the paper are defined the
indexes which, in the real conditions of foundry pig iron production with
sour slags, determine numerical values of K(Mn,Si) and K(Si,S) constants.
The analysis of foundry pig iron production, in the blast furnace of the
Iron Work in Vareš proves that apart form the slag basicity, but also other
components in iron and slag have a considerable influence on the value of
these constants.
Keywords: K(Mn,Si) and K(Si,S) constants, Foundry Pig Iron, Sour Slag, Blast Furnace.
- Type of paper
: Paper in journal
Title: The Continuous Casting of Steel-Present Status and Trends
in the Further Development
- Authors:
- Krajcar, Josip (23143)
Journal: Strojarstvo
Number: 3-4
ISSN: 0562-1887
Volume: 35
Year: 1993
Pages: from 143 to 149
Number of references: 14
Language: hrvatski
Summary: The paper deals with the historical development of
continuous steel casting, the reasons for a fast application, the most
important improvements in the machine design and in the casting process,
the performances of modern continuous casting machines, and the trends in
the further development.
Keywords: Casting machines, Continuous casting of steel, Steel.
- Type of paper
: Paper in journal
Title: Resistance Simulation in Modul by Continuous Casting of
Steel
- Authors:
- Šešerin, Ivica
- Krajcar, Josip (23143)
- Ivanušić, Vera (63094)
- Stojadinović, D.
- Stojadinović, D.
Journal: Metalurgija
Number: 4
ISSN: 0543-5846
Volume: 33
Year: 1994
Pages: from 155 to 159
Number of references: 6
Language: hrvatski
Summary: The increase of the frictional force between the thin
strand shell and the mould causes more cracks and brakouts. Since the total
frictional force can be determined from the acceleration change of the
oscillation system caused by the frictional force, this paper examines the
possibility of its simulation, observing the acceleration change of the
model oscillation system.
Keywords: Continuous casting of steel, the frictional force in mould.
- Type of paper
: Paper in journal
Title: About the Determination of the Mould Oscillation
Parameters in Continuous Casting of Steel
- Authors:
- Ferketić, Vladimir (11634)
- Ivančan, Anka (79316)
- Krajcar, Josip (23143)
Journal: TEHNIKA - Rudarstvo, geologija i metalurgija
Number: 1-2
ISSN: 1318-0010
Volume: 29
Year: 1995
Pages: from 85 to 87
Number of references: 13
Language: engleski
Summary: In determining the oscillation parameters, the relation of
the mould oscillation speed and the casting speed must be considered. A
suitable negative strip ratio must be assured. The mould speed depends on
the product of the amplitude and the frequency. Experience showed that it
is more suitable to cast at low amplitudes and high frequencies. The demand
for a low amplitude arises from the requirement that the displacement of
the mould during the negative strip time must be smaller than the thickness
of the slag layer on the steel meniscus in the mould. In this paper, the
bases for optimization on the oscillation parameters are given, the
relation of this parameters to the behaviour of casting powders, and some
results obtained in Steelworks Sisak are presented.
Keywords: Continuous casting, oscillation parameters.
- Type of paper
: Paper in journal
Title: The Role of Microstructure in Sulphide Stress Corrosion of
High Strength Low Alloyed Steels
- Authors:
- Malina, Marijan (92381)
- Novosel-Radović, Vjera (33706)
- Malina, Jadranka (83026)
Journal: Metalurgija
Number: 1
ISSN: 0543-5846
Volume: 33
Year: 1994
Pages: from 29 to 34
Number of references: 11
Language: hrvatski
Summary: The influence of microstructure on SSC-resistance of
experimental low alloyed Mn-Mo steel has been studied. The results obtained
revealed close connection of SSC with mechanical properties and
microstructure:resistance to corrosion is decreased while yield strength
and hardness are increased by changing beat treatment conditions.
Differences in SSC-resistance are consequence of microstructural parameters
like number of phases, grain size, morphological characteristics and
distribution of carbide particles.
Keywords: HSLA Steel, SSC, Microstructural Changes.
- Type of paper
: Paper in journal
Title: On the Creep Deformation on Single Crystal Ni Base
Supperalloy CMSX-3
- Authors:
- Zrnik, Jozef
- Žitnansky, Marcel
- Mamuzić, Ilija (27862)
Journal: Metalurgija
Number: 1/2
ISSN: 0543-5846
Volume: 34
Year: 1995
Pages: from 7 to 12
Number of references: 13
Language: engleski
Summary: Heat treated specimens of Single crystal nickel base
superalloy were submitted to tension creep at the temperature of 900řC. The
deformation process was investigated at different states of creep. In the
matrix hardened by bimodal precipitates the development of dislocation
structure and precipitates morphology changes were studied by means of TEM
on longitudinal sections of creep deformed samples close to fracture
surfaces. The observation of fracture surfaces shows that fracture induced
by creep damage starts from incipient casting pores of cracks initiated in
carbide precipitates.
Keywords: The creep deformation, the Ni base superalloy, the microstructure
- Type of paper
: Paper in journal
Title: Influence of Cold Deformation on Mechanical
Characteristics of Aluminium Alloy Al-Cu-Bi-Pb
- Authors:
- Jakšić, Drago
- Mamuzić, Ilija (27862)
- Golja, Marijan (57764)
- Curić, Miljena
Journal: Metalurgija
Number: 1/2
ISSN: 0543-5846
Volume: 34
Year: 1995
Pages: from 43 to 46
Number of references: 8
Language: hrvatski
Summary: The work deals with the aluminium alloy, intended for
processing by pressing, of the type Al-Cu-Bi-Pb, the mark 2011 according to
ASTM, from the family of duraluminium, whose main alloy element is copper
and which can be thermally hardened. The aim of this work, is to establish
in the production of round bar products, the influence and optimal
parameters of cold deformation on mechanical characteristics, which are
importante at automated machining.
Keywords: The Cold deformation, the Aluminium Alloy Al-Cu-Bi-Pb, the round bar
- Type of paper
: Paper in journal
Title: The Effect of Structural Characteristics of Strengtheming
Phase on Creep Fatique Bahaviour of Single Crystal Nickel Base Superalloys
- Authors:
- Zrnik, Jozef
- Hazlinger, Marian
- Mamuzić, Ilija (27862)
- Žitnansky, Marcel
Journal: Metalurgija
Number: 3
ISSN: 0543-5846
Volume: 34
Year: 1995
Pages: from 61 to 66
Number of references: 12
Language: engleski
Summary: The effect of different initial microstructures defined by
various precipitates morphology was investigated at the creep/fatique
conditions by 900řC and 500 MPa. The wave form of stress as a function of
time for cyclic loading was of trapezoidal shape with a hold time 10
seconds at the upper stress level. TEM was employed to examine the
deformation process in a strengthened matrix in dependence of precipitate
morphology. The fracture lifetime and cycles up to fracture were the
criteria for the evaluate the additional cyclic component effect on the
course of deformation.
Keywords: The strengthening phase, the structural characteristics, the Ni base superalloy
- Type of paper
: Paper in journal
Title: Resistance to Britlle Fracture by Micro-Alloyed Steels
- Authors:
- Michel, Jozef
- Mamuzić, Ilija (27862)
- Buršak, Marjan
Journal: Metalurgija
Number: 3
ISSN: 0543-5846
Volume: 34
Year: 1995
Pages: from 73 to 78
Number of references: 9
Language: engleski
Summary: The relations between the criteria describing resistance to
brittle fracture considering the variety of experimental results obtained
(using Charpy impact testing, DWTT, DWT and plain stain fracture toughness
tests) are presented. The requestd and certified criteria used in material
standards for the resistance to brittle fracture are presented,
recommendations for changes and new methods for a more precise evaluation
of the resistance to brittle fracture of the these steels are given too.
Keywords: The microalloyed steel, the brittle fracture, the material standard
- Type of paper
: Paper in journal
Title: SSCC-Dependence on Residual Stresses in HSLA Steel
- Authors:
- Malina, Jadranka (83026)
- Novosel-Radović, Vjera (33706)
- Malina, Marijan (92381)
Journal: TEHNIKA - Rudarstvo, geologija i metalurgija
Number: 1-2
ISSN: 1318-0010
Volume: 29
Year: 1995
Pages: from 106 to 108
Number of references: 15
Language: engleski
Summary: Environment sensitive cracking of high strength low alloyed
(HSLA) steels usually occurs in deep sour wells. Hydrogen sulfide dissolved
in water and oil phase has been proved to be the principal species
responsible for sulfide stress corrosion cracking (SSCC). In this work,
resistance to SSCC of an experimental low alloyed Mn-Mo steel was increased
by properly chosen heat treatment conditions. Tensocorrosion tests and
microstructural investigations by x-ray diffraction revealed that residual
stresses are reliable indicator of SSCC-susceptibility.
Keywords: HSLA steel, residual stress, sulfide stress corrosion cracking.
- Type of paper
: Paper in proceedings
Title: Contribution of niobium microalloyed element for
improvement property structural steels tubes
- Authors:
- Rešković, Stoja (57806)
Proceedings title: Zbornik radova 7. Jugoslavenskog simpozija o plastičnosti
Language: hrvatski
Place: Pula
Year: 1991
Pages: from 243 to 246
Meeting: 7. Jugoslavenski simpozij o plastičnosti
Held: from 06/05/91 to 06/07/91
Summary: The paper presents the research results production
andcomprehensive analysis propertys of structural steels tubes ofniobium
microalloyed steel. The tubes of niobium microalloyedsteels estabilsed have
significantly preeferble of property incomparison with to tubes of habitual
quality. On the basis ofsteels properties performed is wall thickness
reduction, withwhat realized the significant wall thicknes reduction ca
beachieved. At the same time this kind of tubes have significantproperty,
priority of yield point, resistance to tearing,weldability and tenacty.
Keywords: Microalloying; Steel tube; Property
- Type of paper
: Paper in proceedings
Title: Comments on weld quality obtained at HF welding of pipes
made of Nb low alloyed steel
- Authors:
- Rešković, Stoja (57806)
- Novosel-Radović, Vjera (33706)
- Preloščan, Andrija (38695)
- Fried, Željko
- Editors
- Rešković, Stoja (57806)
- Novosel-Radović, Vjera (33706)
- Preloščan, Andrija (38695)
Proceedings title: Međunar.savj. "Materijali i zavarivanje u naftnimi petrokemijskim postrojenjima"
Language: hrvatski
Place: Sisak
Year: 1992
Pages: from 123 to 132
Meeting: 7. Jugoslavenski simpozij o plastičnosti
Held: from 11/19/92 to 11/20/92
Summary: Testing were made upon the HF welded pipes made of
Nbmicroalloyed steel, prior to and after hot rolling. Obtainedresults of
testing of microconstituents, parameters ofmicrostructure, mechanical
properties and low temperature impacttoughness indicate a good quality
welding and stable andconsistent toughness values.
Keywords: Microalloyed steel; HF welding; Weld quality
- Type of paper
: Paper in proceedings
Title: Advantage of application niobium microalloyed steel in
production structural steels tubes
- Authors:
- Slošić, V.
- Markotić, Anto (57483)
Proceedings title: Zbornik radova; "CIM '93 - 2. savjetovanje proizvodnog strojarstva"
Language: hrvatski
Place: Zagreb
Year: 1993
Pages: from 13 to 19
Meeting: CIM '93. - 2. savjetovanje proizvodnog strojarstva
Summary: The paper presents the research results of niobium
microalloyedsteel applicatin in production of structural hot rolled
steelsstrips for welded tubes. The obtained results showed that
niobiummicroalloyed tubes have properties remarkably better. On thebasis of
the steels properties the significant wall thicknessreduction can be
achieved.
Keywords: Structural steel; Tube; Microalloying
- Type of paper
: Paper in proceedings
Title: Programme of Reconstruction and Development of Steel
Manufacturing Industry in Croatia
- Authors:
- Markotić, Anto (57483)
- Slošić, V.
- Malina, Marijan (92381)
- Čurković, A.
- Živković, V.
- Županić, S.
Proceedings title: Međunar.savj."Materijali i zavarivanje u naftnim i petrokemijskim postrojenjima"
Language: hrvatski
Place: Sisak
Year: 1992
Pages: from 25 to 43
Meeting: Materijali i zavarivanje u naftnim i petrokemijskim postrojenjima
Held: from 11/19/92 to 11/20/92
Summary: Essentially changed market environment of steel
products,difficulties in business operations and requested restructuringof
steel manufacturing industry in Croatia induced a desing ofprogramme for
reconstruction and development which definestrategy of overcoming existing
difficulties bearing in mind thenew circumstances (independent state).
Also, needed investmentsinto the perspective development and profitable
products andpossibilities to provide required quantities of lacking
steelproducts for home market are considered.
Keywords: Steel fabrication; steel; market; production; processing; reconstruction; development.
- Type of paper
: Paper in proceedings
Title: Contribution of niobium microalloyed element for
inprovement property structural steels tubes
- Authors:
- Rešković, Stoja (57806)
Proceedings title: Zbornik radova; 7. jugoslovenskog simpozija o plastičnosti
Language: hrvatski
Place: Pula
Year: 1991
Pages: from 243 to 246
Meeting: 7. jugoslavenski simpozij o plastičnosti
Held: from 06/05/91 to 06/07/91
Summary: The paper presents the reseach results production
andcomprehensive analysis properties of structural steels tubes ofniobium
microalloyed steel. The tubes of niobium microalloyedsteel established have
significantly prefereable of property incomparison with the tubes of
habitual quality. On the basis ofsteels properties performed is wall
thickness reduction, withwhat realized the significant wall thickness
reduction can beachieved. At the sane time this kind of tubes have
significantproperty, priority of yield point, resistance to
tearing,weldability and tenacty.
Keywords: Microalloying, Steel Tubes, Property
- Type of paper
: Paper in proceedings
Title: Comments on weld quality obtained at HF welding of pipes
made of Nb low alloyed steel
- Authors:
- Rešković, Stoja (57806)
- Novosel-Radović, Vjera (33706)
- Preloščan, Andrija (38695)
- Fried, Željko
Proceedings title: Međunar.savj."Materijali i zavarivanje u naftnim i petrokemijskim postrojenjima"
Language: hrvatski
Place: Sisak
Year: 1992
Pages: from 123 to 132
Meeting: Materijali i zavarivanje u naftnim i petrokemijskim postrojenjima
Held: from 11/19/92 to 11/20/92
Summary: Testings were made upon the HF welded pipes made of
Nbmicroalloyed steel, prior to and after hot rolling. Obtainedresults of
testing of microconstituents, parametars ofmicrostructure, mechanical
properties and low temperature impacttoughness indicate a good quality
welding and stable andconsistent toughness values.
Keywords: Microalloyed Steel, HF Welding, Weld Quality
- Type of paper
: Paper in proceedings
Title: Adventage of application niobium microalloyed steel in
production structural steels tubes
- Authors:
- Rešković, Stoja (57806)
Proceedings title: CIM '93. - 2. savjetovanje proizvodnog strojarstva
Language: hrvatski
Place: Zagreb
Year: 1993
Pages: from 13 to 19
Meeting: CIM '93. - 2. savjetovanje proizvodnog strojarstva
Held: from 11/01/93 to 11/03/93
Summary: The paper presents the research results of niobium
microalloyedsteel application in production of structural hot rolled
steelsstrips for welded tubes. The obtained results showed that
niobiummicroalloyed tubes have properties remarkably better. On thebasis of
the steels properties the significant wall thicknessreduction can be
achieved.
Keywords: Structural, Steel, Tubes, Microalloying
- Type of paper
: Paper in proceedings
Title: Programme of reconstruction and development of steel
manufacturing industry in Croatia
- Authors:
- Markotić, Anto (57483)
- Čurković, A.
- Malina, Marijan (92381)
- Živković, V.
- Županić, S.
- Boras, Ivica
Proceedings title: Međunar.savj."Materijali i zavarivanje u naftnim i petrokemijskim postrojenjima"
Language: hrvatski
Place: Sisak
Year: 1992
Pages: from 25 to 43
Meeting: Materijali i zavarivanje u naftnim i petrokemijskim postrojenjima
Held: from 11/19/92 to 11/20/92
Summary: Essentially changed market environment of steel
products,difficulties in business operations and requested restructuringof
steel manufacturin industry in Croatia induced a desink ofprogramme for
reconstruction and development which will definestrategy of overcoming
existing difficulties bearing in mind thenew circumstances (independent
state). Also, needed investmentsinto the perspective development and
profitable products andpossibilities to provide required quantities of
lacking steelproducts for home market are considered.
Keywords: Steel Fabrication, Steel, Market, Production, Processing, Reconstruction, Development
- Type of paper
: Paper in proceedings
Title: Measurement for testing the action of casting powder at
continuous casting of steel
- Authors:
- Krajcar, Josip (23143)
- Medved, F.
- Buško, Grgo
- Nikolić, Đurđica
Proceedings title: 37. međunarodni godišnji skup KOREMA
Language: hrvatski
Place: Zagreb
Year: 1992
Pages: from 383 to 385
Meeting: CIM '93. - 2. savjetovanje proizvodnog strojarstva
Held: from 06/16/92 to 06/17/92
Summary: The measurements of two main characteristic which can be
used toevaluate the action of casting powder during continuous castingof
steel are described. The heat insulation ability wasdetermined by measuring
the temperature across the powder layerand the heat flux density through
the layer. The lubricationability was determined by measuring the power of
the oscillatormotor and by the signal produced moving a magnet in an
inductor.The results were compared with other acchieved by using
differentmethods. The necessity of introduction improved
continuousmeasurement during casting is pointed out.
Keywords: Casting Powder, Coninuous Casting of Steel
- Type of paper
: Paper in proceedings
Title: Determination of the Friction Forse in the hould at
Continuous Casting of Steel Measuring the Acceleration
- Authors:
- Krajcar, Josip (23143)
- Šešerin, Ivica
- Stojadinović, D.
- Ivanušić, Vera (63094)
Proceedings title: 38. Međunarodni godišnji skup KoREMA
Language: hrvatski
Place: Zagreb
Year: 1993
Pages: from 430 to 431
Meeting: 38. međunarodni godišnji skup KoREMA
Held: from 04/26/93 to 04/28/93
Summary: The friction force at continuous castings of steel
represents thedifference between the force acting at the mould
oscillationduring casting and in the idle motion. For the measurement
ofthis force more methods are used: extension band, load cell andpower of
the oscillator motor. In this work the friction forcewas determined from
the difference of the acceleration measuredby a vibrometer: at the idle
oscillation, with load of known massand during casting. The method does not
require the insertion ofsensors in the parts of the oscillation system. The
acchievedvalues of friction force depend on the oscillation parameter.
Keywords: Continuous Casting, Friction Force, Lubrication
- Type of paper
: Paper in proceedings
Title: Determination of conditions for production of pipes higher
quality API grade
- Authors:
- Gojić, Mirko (63390)
- Balenović, Marijan (139043)
Proceedings title: Zbornik del za IX. posvetovanje valjarjev
Language: hrvatski
Place: Štore, Slovenija
Year: 1990
Pages: from 453 to 461
Meeting: IX. posvetovanje valjarjev
Held: from 05/16/90 to 05/18/90
Summary: In the paper shown the results of mechanical properties
andmicrostructures for production tubing and caring pipes for oilindustry
from low alloyed Mn-V and Cr-Mo-Nb steel.
Keywords: Low Alloyed Steel, Heat Treatment, Tubing and Caring Pipes, Mechanical Properties
- Type of paper
: Paper in proceedings
Title: Heat treatment of the tubes from low alloyed steels for
oil industry
- Authors:
- Gojić, Mirko (63390)
Proceedings title: Znanstveno-stručno savjetovanje "Toplinska obrada metala"
Language: hrvatski
Place: Zagreb
Year: 1992
Pages: from 21 to 29
Meeting: Toplinska obrada metala
Held: from 06/17/92 to 06/17/92
Summary: This work deals with series of the heat treatment variants
on theindustrial rolled tubing from low-alloyed Mn-V steel, as well asfrom
low-alloyed Cr-Mo steel which is microalloyed with Nb.
Keywords: Heat Treatment, Low Alloyed Steel, Mechanical Properties
- Type of paper
: Paper in proceedings
Title: Some aspects of development of low alloyed steel for pipes
used for oil industry service
- Authors:
- Gojić, Mirko (63390)
- Balenović, Marijan (139043)
Proceedings title: Materijali i zavarivanje u naftnim i petrokemijskim postrojenjima
Language: hrvatski
Place: Sisak
Year: 1992
Pages: from 105 to 112
Meeting: Materijali i zavarivanje u naftnim i petrokemijskim postrojenjima
Held: from 11/19/92 to 11/20/92
Summary: Results of testing indicate that heat treatment (quenching
andhigh annealing) may produce high corrosion resistance, expressedin term
of critical stress value (Sc), which is at level or evenhigher than
yielding stress.
Keywords: Low Alloyed Steel, Tubing, Microstructure, Corrosion, Critical Stress
- Type of paper
: Paper in proceedings
Title: The effect of a Gas Balance Mistake on the Process of
Steel Production Conduct
- Authors:
- Kundak, Mijo (24642)
- Črnko, Josip (57413)
Proceedings title: 37. međunarodni godišnji skup KoREMA
Language: hrvatski
Place: Zagreb
Year: 1992
Pages: from 711 to 712
Meeting: CIM '93. - 2. savjetovanje proizvodnog strojarstva
Held: from 04/26/92 to 04/27/92
Summary: The paper refers to the main possibilities of melt
heatingconduct in the steel production by the means of a process balanceof
carbon and CO and CO2 gases coming of melting loss of carboncontained in
the melt. Besides, it gives a list of factorseffecting the mistakes of a
process gas balance.
Keywords: Steel production, Open-hearth furnace, Gas balance, Mistakes
- Type of paper
: Paper in proceedings
Title: The Periodic Reparation of Insulators and Its Effect on
the Energy Consumption in Pusher Furnace Used in Sisak Ironworks, Croatia
- Authors:
- Črnko, Josip (57413)
- Kundak, Mijo (24642)
Proceedings title: Zbornik prednašok z medzinarodnej konferencie pri priležitosti 40.vyročia založe
Language: engleski
Place: Košice, Slovačka
Year: 1992
Pages: from 27 to 39
Meeting: Zbornik Prednašok z medzinarodnej konferencie pri prileznosti 40 vyrocila zaloze energeticke premeny v hutnickich prevadzkach, Kosice
Held: from 09/02/92 to 09/05/92
Summary: In Sisak Ironworks' strip and billet rolling mill two
pusherfurnaces of an American Rust Furnace Co. desiven have been usedfor
slabs heating. Improving their work, regarding both betterutilization of
heating energy and endurance of the walls as wellas the quality of the
technological functions, leads to adecrease of a specific heat energy
consumption per unit of aproduct. In the context of this paper, the effect
of skid railcarriers coatin abrasion and a hearth bottom growth on
thespecific heat energy consumption as well as the effect of othertechnical
and technological characteristics of the heatingfurnaces named have been
particularly analyzed.
Keywords: Pusher furnace, Skid rail, Coating abrasion, Energy, Consumption
- Type of paper
: Paper in proceedings
Title: Some aspects in development of steels with better
corrosion properties for agressive conditions of exploitation
- Authors:
- Malina, Jadranka (83026)
- Gojić, Mirko (63390)
- Sefaja, Jasmina
- Malina, Marijan (92381)
Proceedings title: Zbirka referata 10. savjetovanja o zaštiti materijala i industrijskom finišu
Language: hrvatski
Place: Zagreb
Year: 1992
Pages: from 69 to 73
Meeting: 10. savjetovanje o zaštiti materijala i industrijskom finišu
Held: from 06/18/92 to 06/19/92
Summary: Two low-alloyed Mn-V steels differing in sulfur content
(0,005 %and 0,028 %) were hydrogen charged in two different stresscorrosion
test. All specimens fractured after charging revealedbrittleness, with less
ductibility - loss in steel with moresulfur. The same steel also had better
resistivity to sulfidestress corrosion cracking, what was ascribed to more
orderedmicrostructure obtained by heat treatment (normalizing). Thehighest
resistivity to hydrogen embrittlement has shown the lowsulphur steel after
normalizing and tempering.
Keywords: Medium carbon Mn-V steel, Stress corrosion craking, Influence of sulfur and heat treatment, Hydrogen embrittlement
- Type of paper
: Paper in proceedings
Title: Blistering and stepwise cracking of line pipe for oil
industry
- Authors:
- Malina, Jadranka (83026)
- Iharoš, Ana
- Malina, Marijan (92381)
Proceedings title: Materijali i zavarivanje u naftnim i petrokemijskim postrojenjima
Language: hrvatski
Place: Sisak
Year: 1992
Pages: from 311 to 320
Meeting: Materijali i zavarivanje u naftnim i petrokemijskim postrojenjima
Held: from 11/19/92 to 11/20/92
Summary: A laboratory testing of blistering and stepwise
crackingsusceptibility for longitudinal welded line pipe from low
carbonMn-steel (X-60) was performed. Obtained values for blisteringextent
and SWC -coefficients are significantly higher than thoseexpected, thus
indicating a great susceptibility to hydrogeninduced cracking. Specimen cut
from welded joint showed betterproperties than base material.
Keywords: Longitudinal welded line pipe for oil industry, Hydrogen embrittlement, Stepwise cracking, Blistering
- Type of paper
: Paper in proceedings
Title: Influence of heat treatment on the corrosion resistance of
tubing
- Authors:
- Malina, Marijan (92381)
- Gojić, Mirko (63390)
- Malina, Jadranka (83026)
Proceedings title: Materijali i zavarivanje u naftnim i petrokemijskim postrojenjima
Language: hrvatski
Place: Sisak
Year: 1992
Pages: from 81 to 89
Meeting: Materijali i zavarivanje u naftnim i petrokemijskim postrojenjima
Held: from 11/19/92 to 11/20/92
Summary: For heat treated (industrial and laboratory conditions)
tubing,critical stress is determined by Shell-method. Results
ofinvestigations show that microstructure and yield strenght
affectdominantly the occurance of sulfide stress corrosion
cracking.Commercially available Č.4732 steel may be adequate to L-80grade,
if normalized and tempered, but for higher qualityrequirements,
micro-alloyed Cr-Mo steel should be used.
Keywords: Heat treatment, Corrosion, Low-alloyed Cr-Mo steel, tubing
- Type of paper
: Paper in proceedings
Title: Contribution Investigation Steel Flow Stress by Holloman's
Method
- Authors:
- Golja, Marijan (57764)
- Mamuzić, Ilija (27862)
- Kolar, Željka
Proceedings title: Simpozij o plastičnosti
Language: hrvatski
Place: Pula
Year: 1991
Pages: from 238 to 242
Meeting: 7. jugoslavenski simpozij o plastičnosti
Held: from 06/05/91 to 06/07/91
Summary: In the work the design of user programme for the analysis
ofexperimental data for metal flow stress and the results of
suchdeterminations of metal flow stress for several steel grades havebeen
presented.
Keywords: Steel Flow Stress,
- Type of paper
: Paper in proceedings
Title: Deformation Resistance of Highstrength Construction Bainit
Steel
- Authors:
- Križanić, Rade (23663)
- Mamuzić, Ilija (27862)
- Nikolić, Đurđica
Proceedings title: Simpozij o plastičnosti
Language: hrvatski
Place: Pula
Year: 1991
Pages: from 247 to 253
Meeting: 7. jugoslavenski simpozij o plastičnosti
Held: from 06/05/91 to 06/07/91
Summary: At first was given a short teoretical rewiew of
highstrengthconstruction bainit steel with Rv up 600 MPa and Rm up 750
MPa.At various variants thermomechanical forming and criticaldeformation
was investigated.
Keywords: Deformation resistance, Bainit steel, Deformation speed
- Type of paper
: Paper in proceedings
Title: The Expert Systems in Ecology of Metallurgy
- Authors:
- Mamuzić, Ilija (27862)
- Drujan, Vladimir
- Garan, Vjačeslav
Proceedings title: Internacional Conference Metallurgy EAST-WEST 93
Language: engleski
Place: Košice, Slovačka
Year: 1993
Pages: from 170 to 179
Meeting: International Conference Metallurgy EAST-WEST 93
Held: from 10/11/93 to 10/14/93
Summary: Besides the paper on which the expert system is built, the
aim ofthe papers is to create the atomatized programme technicalobservation
ecological continuous system of formation andprediction of gaseous dust
consequences in technologicalaggregate of metalurgien plants. The are used
adaptedmathematical models.
Keywords: Expert system, Ecology, Automatized programme, Adapted mathematical model
- Type of paper
: Paper in proceedings
Title: Metal Products, with Special Concern to Pepes, Current
Achnements Related to Applications in Petrochemical Plants
- Authors:
- Mamuzić, Ilija (27862)
Proceedings title: Materijali i zavarivanje u naftnim i petrokemijskim postrojenjima
Language: hrvatski
Place: Sisak
Year: 1992
Pages: from 45 to 52
Meeting: Materijali i zavarivanje u naftnim i petrokemijskim postrojenjima
Held: from 11/19/92 to 11/20/92
Summary: Together with kinds of materials applied in oil and
petrochemicalplants, new changes in world metallurgical
production,requirements specified for metal products and future trends
indevelopment of technological processes are presented. Specialconcern has
been given to the curent state and development ofpipes in the world, both
seam and seamless
Keywords: Metal products, metallurgy, Properties of material, Working processes, Steel pipes
- Type of paper
: Paper in proceedings
Title: Thermomechanical Hightemperature Rolling Conditions of
Highstrength Construction Strip and Billet Bainit Steel
- Authors:
- Križanić, Rade (23663)
- Mamuzić, Ilija (27862)
- Nikolić, Đurđica
Proceedings title: KoREMA 37/1992 Part 2
Language: hrvatski
Place: Zagreb
Year: 1992
Pages: from 22 to 27
Meeting: CIM '93. - 2. savjetovanje proizvodnog strojarstva
Held: from 06/16/92 to 06/17/92
Summary: The paper includes application of reseaching results on
plantsand in production process of rolled strips in the conditions
ofthermomechanical forming.
Keywords: Rolling, bainit steel, hot rolled strip, natural deformation resistance, real deformation resistance
- Type of paper
: Paper in proceedings
Title: The importance of mathematical models in development of
energeticly more rational processes of metal production and recycling of
metal waste
- Authors:
- Črnko, Josip (57413)
Proceedings title: Dodatni izvori i racionalno gospodarenje energijom
Language: hrvatski
Place: Pula
Year: 1994
Pages: from 127 to 134
Meeting: Dodatni izvori i racionalno gospodarenje energijom
Held: from 04/20/94 to 04/22/94
Summary: The aim of the work is to discuss basic advantages deriving
from mathematical modelling of processes and acquainting with potential
possibilities of application of these techniques to develop new processes
of metal production and recycling of metal waste using energeticly more
rational processes.
Keywords: Mathematical modelling, Production and recycling of metal, Decreasing of energy consumption
Other: Organizator savjetovanja: DELIT - Društvo elektrotehničkih
inženjera i tehničara Sisak
- Type of paper
: Paper in proceedings
Title: The influence of niobium precipitates in low-alloy steel
on the change of austenite grain size
- Authors:
- Preloščan, Andrija (38695)
- Preloščan, Mira
Proceedings title: International Sceintific Conference on the Occasion of the 35th Annioversary
Language: engleski
Place: Košice, Slovačka
Year: 1994
Pages: from 502 to 506
Meeting: International Sceintific Conference on the Occasion of the 35th Anniversary
Held: from 06/21/94 to 06/23/94
Summary: The influence of niobium prcipitates in low-alloy steel on
the change of the austenite grain size has been studied. The effect of the
microalloying element in high temperature variant (1230řC) and low
temperature variant (1050řC) of thermomechanical treatment has been
investigated. The isolation and identification procedure of niobium
carbonitrides and the analysis of the microstructural change by Saltykov
have been used.
Keywords: Low-alloy steel, Niobium precipitates, Austenite grain size
- Type of paper
: Paper in proceedings
Title: Influence of steel heating optimization prior to plastid
deformation on energy consumption
- Authors:
- Kundak, Mijo (24642)
Proceedings title: Dodatni izvori i racionalno gospodarenje energijom
Language: hrvatski
Place: Pula
Year: 1994
Pages: from 11 to 15
Meeting: Dodatni izvori i racionalno gospodarenje energijom
Held: from 04/20/94 to 04/22/94
Summary: This paper gives a survey of the influence of temperature
regime optimization in heating furnaces on energy consumption.
Keywords: Steel heating optimization, plastic deformation, energy consumption
- Type of paper
: Paper in proceedings
Title: The influence of energy consumption on economy of steel
and hot rolled products production
- Authors:
- Kundak, Mijo (24642)
- Črnko, Josip (57413)
Proceedings title: Zbornik radova 39.godišnji skup KoREMA
Language: hrvatski
Place: Zagreb
Year: 1994
ISBN/ISSN: 953-6037-02-5
Pages: from 375 to 379
Meeting: 39.godišnji skup KoREMA
Held: from 04/25/94 to 04/27/94
Summary: Due to higher energy expenses in steel production and
processing a parallel analysis of energy consumption in production of
low-carbon steels by means of modern treatments in the world and in the
Republic of Croatia has been done and it can be used when making decisions
on revival and development of black metallurgy in Croatia. In the
background of the analysis a possibility of decreasing of energy
consumption in present conditions of steel production and processing has
been pointed out on the example of the rolling mills in Sisak Ironworks
Holding where otherwise the energy costs for, e.g., 1990. reach more than
40% of the cost price of finished hot rolled products.
Keywords: Energy consumption, steel production economy
- Type of paper
: Paper in proceedings
Title: Contribution to optimalization to melts heating in steel
production by means of waste gases analysis
- Authors:
- Kundak, Mijo (24642)
Proceedings title: Zbornik radova KoREMA 40
Language: hrvatski
Place: Zagreb
Year: 1995
ISBN/ISSN: 953-6037-02-5
Pages: from 396 to 400
Meeting: 40. međunarodni godišnji skup KoREMA
Held: from 04/19/95 to 04/21/95
Summary: The possibility of continuous montoring of melt carbon
content is presented in this paper on the basis of the burning of fuel and
CO comming out of the melt. Based on the known melt carbon content the
required melt temperature may be controlled by more or less supply of fuel
(or power) without measuring its temperature on the basis of energy
balance. Production results of monitoring the analysis of waste gases are
shown and through them the carbon content in the melt during the refining
process in open hearth furnace aswell as the most influencial factors of a
possible failure. The obtained results may be beneficially used at crucible
melt punfyrng after the casting steel.
Keywords: Optimization of control/management, melt heating in steel production, analysis of waste gases
- Type of paper
: Paper in proceedings
Title: Research of resistance to wear of Cast rolls
- Authors:
- Mamuzić, Ilija (27862)
- Gorjanoj, Vjačeslav
Proceedings title: 12.Međunarodno savjetovanja BIAM 94
Language: hrvatski
Place: Zagreb
Year: 1994
Pages: from 8 to 11
Meeting: 12. Međunarodno savjetovanje BIAM 94
Held: from 06/23/94 to 06/24/94
Summary: The resistance to wear of rolls cast of Cr-Ni-Mo-iron was
researched by modelling with laboratory devices. The microstructural
analysis determined that material resistance to wear increased by
decreasing of conditional dimension of carbide and by increasing of the
carbide phase length.
Keywords: The resistance to wear, the roll cast, the carbide
- Type of paper
: Paper in proceedings
Title: Research of deformation resistance of highhard weldable
structural Steel
- Authors:
- Križanić, Rade (23663)
- Hensel, Arno
- Mamuzić, Ilija (27862)
- Nikolić, Đurđica
Proceedings title: 12. Međunarodno savjetovanje BIAM 94
Language: hrvatski
Place: Zagreb
Year: 1994
Pages: from 17 to 21
Meeting: 12. Međunarodno savjetovanje BIAM 94
Held: from 06/23/94 to 06/24/94
Summary: Results of research refer to deformation resistance of
highhard welabl steel with hension yield strength above 600 MPa. It belongs
to low-perlite stelsgroup. Itis microalloyed with Nb, lowalloyed with Cr,
Mn, Mo and Ni. In rolled state, it has bainite structure. On the basis of
the results of research work mathematic terms deformation were determined.
They shov dependance of natural deformation resistance upon test
temperature, speed of deformation and deformation grade of 18,1%. Simce the
state of steel depends upon conditions of thermo-mechanical finishing two
variants were included: austenitizing temperature of 1100řC and 1050řC,
austenitizing time was 20 min. The results of research are represented in
formulas, tables and graphs.
Keywords: The deformation resistance, the structural steel, thermomechanical finisting
- Type of paper
: Paper in proceedings
Title: The Investigation of the Metal Forming Processes Using
Nonlinear Programming Technique
- Authors:
- Binkevich, Irina
- Mamuzić, Ilija (27862)
- Medvedeva, Ludmila
Proceedings title: Proceeding of the 1st Congress of Croatian Society of Mechanics
Language: engleski
Place: Pula
Year: 1994
Pages: from 505 to 510
Meeting: Proceeding of the 1st Congress of Croatian Society of Mechanics
Held: from 09/14/94 to 09/17/94
Summary: The problem of compression of a long compact or perforated
sprig by a flat punch is investigated. The solution is based on the
slip-theory. Matrix operators and nonlinear programming technique are used
to get numerical results. The distribution of stresses and displacements in
the strip is obtained.
Keywords: Slip-line theory, nonlinear programming, strip, stress
- Type of paper
: Paper in proceedings
Title: Mathematical Model of Nitrogen Oxide Generation
- Authors:
- Lazić, Ladislav (105552)
Proceedings title: Zbornik radova KoREMA 39 (1994), 1. svezak
Language: hrvatski
Place: Zagreb
Year: 1994
ISBN/ISSN: 953-6037-02-5
Pages: from 384 to 387
Meeting: 39.godišnji skup KoREMA
Held: from 04/25/94 to 04/27/94
Summary: This paper presents the mathematical model for
determination of the amount of nitrogen oxides generated in the combustion
process of gaseous fuel in industrial furnace ireboxes.
Keywords: Nitrogen oxide, Combustion process, Industrial furnace irebox.
- Type of paper
: Paper in proceedings
Title: Applied Finite Element Method in Thermal Analysis
- Authors:
- Lazić, Ladislav (105552)
Proceedings title: Zbornik radova IV. Međunarodne konferencije "Energeticke premeni v priemysle"
Language: engleski
Place: Košice, Slovačka
Year: 1994
Pages: from 19 to 25
Meeting: 12. Međunarodno savjetovanje BIAM 94
Held: from 09/06/94 to 09/08/94
Summary: The main objctive of this text is to provide a basic
introduction to a general concept and the aplication of the finite element
method to thermal problems. The basic governing equations of the heat
conduction with the appropriate initial and boundary conditions are
presented. A brief discusion of the finite element approach is given
including a comparison with the finite difference technique.
Keywords: Finite element method, Thermal analysis, Heat conduction.
- Type of paper
: Paper in proceedings
Title: Construction of Fluidized-bed Combustion Chamber for
Low-Efficiency Boilers
- Authors:
- Lazić, Ladislav (105552)
- Horbaj, Peter
Proceedings title: Zbornik radova 3. europske konferencije "Industrial Furnaces and Boilers"
Language: engleski
Place: Lisbon, Portugal
Year: 1995
Pages: from 1 to 8
Meeting: Proceeding of the 1st Congress of Croatian Society of Mechanics
Held: from 04/18/95 to 04/21/95
Summary: The technology of two-stage fluidized-bed combustion has
proven to allow burning of low-energy coals with high ash and moisture
content in a way that is economically and ecologically more acceptable than
the conventional layer burning. This paper describes a computation
algorithm and the design and construction of a fluid-bed combustion chamber
with flat mechanical stokers in order to faciliate combustion.
Keywords: Fluidized-bed combustion process, Combustion chamber, Low-energy coal.
- Type of paper
: Paper in proceedings
Title: Characteristics of the surface quality of continuous cast
blooms for seamless tubes in Sisak
- Authors:
- Ferketić, Vladimir (11634)
- Krajcar, Josip (23143)
- Ivančan, Anka (79316)
Proceedings title: Zbornik radova Internacionalne znanstvene konferencije u čast 35.godišnjice Odje
Language: engleski
Place: Košice, Slovačka
Year: 1994
Pages: from 153 to 160
Meeting: International Sceintific Conference on the Occasion of the 35th Anniversary
Held: from 06/21/94 to 06/23/94
Summary: The kinds of oscillation marks and the main surface defects
on the bloom surface are presented. The causes of the defects are
considered and the role of casting powders and of the oscillation
parameters are pointed out.
Keywords: Continuous casting of steel, the surface quality.
Other: Rad je tiskan u Zborniku radova Internacionalne znanstvene
konferencije u čast 35. obljetnice Odjela za crnu metalurgiju i ljevarstvo
Metalirškog fakulteta Visoke tehničke škole u Košicama, Slovačka.
- Type of paper
: Paper in proceedings
Title: The Influence of the Surface Threatmend on the Protection
Quality of Seamless Steel Tubing
- Authors:
- Lončar, Mirjana
- Novosel-Radović, Vjera (33706)
- Rešković, Stoja (57806)
Proceedings title: Zbornik radova 11.savjetovanja o zaštiti materijala i industrijskom finišu
Language: hrvatski
Place: Zagreb
Year: 1994
Pages: from 49 to 58
Meeting: 11. savjetovanje o zaštiti materijala i industrijskom finišu
Held: from 06/23/94 to 06/24/94
Summary: The paper represents the research of the influence of the
condition of pickled and thermally treated surface on the quality of
operation for temporary protection of seamless steel tubing. It was found
that, in the presence of oxidation, a significant amount of oxsidelayers
Fe3O4, as the basic phase, and other ferrous oxside Fe2O3 and FeO are
formed on the surface of hot-rolled seamless steel tubing. The scanning
x-ray analysis of pickled samples in sulfuric acid, in operating
conditions, has shown the presence of remaining oxide layers-scale and the
occurence of clean metal surface at the same time. With the thermal
treatment, the sharee of oxide layers-scale is significantly increased. The
protective coat discontinuously covers such a surface. The best results
have been obtained with laboratory pickling, thermal treatment, and with
the protection of hot-rolledseamless tubing at controlled pickling
parameters(bath composition and temperature, pickling time, washing out
after pickling) and the atmosphere in the thermal treatment oven. The best
results have been obtained by sand blasting of oxside
layers-scale(mechanical method).
Keywords: Carbon steel, scale-oxide layer, pickling processes, bitumen coating.
- Type of paper
: Paper in proceedings
Title: Corrosion Stability of Modificated Silicon Cast Iron
- Authors:
- Malina, Jadranka (83026)
- Unkić, Faruk
- Kolarević, Željko
Proceedings title: Zb. radova 11.savjetovanja o zaštiti materijala i industrijskom finišu
Language: hrvatski
Place: Zagreb
Year: 1994
Pages: from 94 to 100
Meeting: 11. savjetovanje o zaštiti materijala i industrijskom finišu
Held: from 06/23/94 to 06/24/94
Summary: The influence of modificator addition on microstructure and
corrosion ewsistance of high silicon cast iron was studied. For this
purpose a SiCa-modificator and complex modificator FeTi +FeSiMg5CeMM have
been used. Corrosion tests by the mass-loss method were performed at 60řC
in 1M, 2M and 6M H2SO4. Metallographic analysis of microstructure revealed
that by modification of high silicon cast iron, a different graphit
distribution and morphology - from flakes to nodules - can be achieved,
what resulted in a different corrosion resistance of specimens examined.
Keywords: High silicon cast iron, modification, corrosion stability.
- Type of paper
: Paper in proceedings
Title: Environmentally Assisted Cracking in HSLA Steels
- Authors:
- Malina, Jadranka (83026)
Proceedings title: Zb.radova skupa "Agresivnost medija i pouzdanost opreme"
Language: hrvatski
Place: Slavonski Brod
Year: 1994
Pages: from 65 to 80
Meeting: Znanstveno stručni skup "Agresivnost medija i pouzdanost opreme"
Held: from 10/06/94 to 10/06/94
Summary: Industry wide, about 25% of inspected pressure wessels
operating in wet H2S service contained cracks. Numerous damages are the
result of chemomechanical interaction of metal lattice with atomic hydrogen
generated from aggressive environments. Brittle fracture failures of vital
equipment drive the producers of steel and researchers to elucidate the
phenomenon of hydrogen embrittlement, so that better materials with longer
life and greater safety could be produced. In this paper an atempt is made
to rewiew some of many different aspects in hydrogen interaction with
metals.
Keywords: Low alloyed steel, hydrogen embrittlement, H2S-environment.
- Type of paper
: Paper in proceedings
Title: Production technology - limiting factor in producing of
corrosion resistant OCTG
- Authors:
- Malina, Marijan (92381)
- Malina, Jadranka (83026)
Proceedings title: Zbornik referatov Posvetovanja"Produktna tehnika in podjetništvo v kemični in pr
Language: hrvatski
Place: Maribor, Slovenija
Year: 1994
Pages: from 27 to 33
Meeting: Posvetovanje "Produktna tehnika in podjetništvo v kemični in procesnih industrijah"
Held: from 10/18/94 to 10/19/94
Summary: Exposed to the extremely aggressive environment of deep
sour wells, oil country tubular goods are expected to satisfy both, demands
for high mechanical performances and also high corrosion resistance to
brittle sulfide stress cracking. Development of such OCTG-products relies
on adequate chemical composition of steel used, as well as on production
technology possibilities. Corrosion and mechanical properties of low
alloyed Mn-V tubing were investigated depending on heat treatment
procedures. Two different regimes of HT have been performed regarding
disposable equipment in Željezara Sisak. Tensocorrosion tests,
metallographic inspections and fractographic analyses revealed that heat
treatment by quenching and tempering at higher temperatures resulted in a
microstructure which provides better mechanical and corrosion resistance.
Results obtained are input parameters in the know-how triade
TECHNOLOGY-MICROSTRUCTURE-PROPERTIES, what is obligatory cycle in new
products research and development.
Keywords: Oil country tubular goods, Heat treatment, Production technology.
- Type of paper
: Paper in proceedings
Title: Phase Transformation of Niobium in Final Thermomechanical
Treatment of Microalloyed Steel
- Authors:
- Rešković, Stoja (57806)
- Novosel-Radović, Vjera (33706)
- Preloščan, Andrija (38695)
Proceedings title: Zb.radova Internac.znan.konf.u čast 35.obljetnice, Košice
Language: engleski
Place: Košice, Slovačka
Year: 1994
Pages: from 79 to 84
Meeting: International Sceintific Conference on the Occasion of the 35th Anniversary
Held: from 06/21/94 to 06/23/94
Summary: In the metallurgical practice it is know that niobium
microalloyed leed to strenthening low-carbon structural steel. By reason of
increase affinity of niobium to carbon and nitrogen come during the
thermomechanical treatment to precipitatic adequate quantity stable
carbide, nitride and carbonitride. They come to stopping mechanismes of
precipitation carbonitride niobium with mechanismes recrystallizations and
recovery is no explained completely. Because that we wanted to explain
microstructural changes during the final thermomechanical treatment. For
basis of these investigation we are used also before obtained results.
Keywords: Phase transformation, niobium microalloyed steel, thermomechanical treatment.
- Type of paper
: Summary in proceedings
Title: The influence of electrolyte composition on new phases
deposition at steel surface
- Authors:
- Šešerin, Ivica
- Malina, Jadranka (83026)
- Marjanović, Tihana
Proceedings title: XIII. skup hrvatskih kemičara
Language: hrvatski
Place: Zagreb
Year: 1993
Pages: from 219 to 219
Meeting: XIII. skup hrvatskih kemičara
Held: from 02/08/93 to 02/10/93
Summary: Solid phase formed at interface steel N-80/electrolyte
depend onsolution chemistry. In sulfuric acid, sodium chloride
andriver-water Fe(II) - and Fe(III)- oxides and oxyhydroxides
wereidentified (X-ray diffraction), until in acidochloridic mediumwith H2S
saturated, predominantly Fe-sulfides crystallized. Inriver-water deposit
CaCo3 is also present.
Keywords: Interface steel N-80/electrolyte, Deposit, Solid phase constitution, Fe-oxides
- Type of paper
: Summary in proceedings
Title: Specific surface determination of thermally formed iron
oxide layer
- Authors:
- Malina, Jadranka (83026)
- Ivanušić, Vera (63094)
Proceedings title: Zbornik sažetaka radova "Od uzorka do podataka i informacija"
Language: hrvatski
Place: Zagreb
Year: 1993
Pages: from 54 to 55
Meeting: Međunarodno savjetovanje "Materijali i zavarivanje u naftnim, petokemijskim postrojenjima"
Held: from 10/20/93 to 10/23/93
Summary: The specific surface area of oxide layer thermally formed
onsteel filings by heating at 773 K for one hour under 25 dm3/h ofO2, was
obtained. X-ray diffraction analysis of composition andstructure has shown
that 15-25 micrometers thick oxide scaleconsisted of 90 % Fe3O4 and 5 %
ŕ-Fe2O3, with neglectablefraction of š-Fe2O3 and š-FeO(OH).
Specific surface was obtained by dye adsorption method, based onFe-oxide
susceptibility to become charged in water solution andthus having the
tendency to adsorb polar molecules, likemethylene blue, MeB. Adsorption on
the oxidized filings wasregistered by spectrophotometric determination of
MeBconcentration and Langemuir adsorption isotherm, from which thespecific
surface can be derived.
Keywords: Thermally formed Fe-oxide, Organic dye adsorption, Specific surface area, Langemuir adsorption isotherm
Other: Međunarodno znanstveno savjetovanje; izdavač je CROSS
(CroatianSystem Society)
- Type of paper
: Ph.D.
Title: Possibilities of control of melt heating in open-hearth
furnace by means of continuous follow-up flue gas analysis in the vertical
canal of furnace head
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Author: KUNDAK MIJO
Date of defense: 01/09/91
Language: hrvatski
Number of pages: 115
Summary: A literary review of the development of open-heart
steelproduction has been given in the work with special regard to
thepresent achievements in balacing carbon content and melttemperature in
the refining process as well as optimal control ofthermal regulation.
The work is directed to seeking adequate influence ofdecarbonication, which
is calculated by means of flue gasanalysis in the vertical canal of furnace
head and otherparameters in open hearth furnaces, upon fuel consumption. It
hasbeen shown that melt heating during the refining process withoxygen
injection without fuel feeding is impossible in smalleopen-hearth furnaces.
The method of carbon content follow-up has been in proved in therefining
process by means of flue-gas analysis in the verticalcanal of furnace head.
The accuracy of carbon content follow uphas been increased by flue gas
analysis in the vertical canal inthe relation to the analysis of flue gas
in the common flue.
In the concluzion of this work optimal necessary flow mass ofmasut for
continuous control of melt heating in the refiningprocess obtained by means
of model has been shown depending ondecarbonisation rate and other
parameters without continuousmeasurement of melt temperature.
Keywords: Possibility, Control, Melt Heating, Analysis, Flue Gas, Open-Hearth Furnace
- Type of paper
: Ph.D.
Title: Contribution to modelling and optimization of material
heating process in rolling mill heating furnaces
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Author: LAZIĆ LADISLAV
Date of defense: 03/16/91
Language: hrvatski
Number of pages: 173
Summary: This paper presents the possibilities of more rational use
ofenergy in order to save fuel, intensity the technological process,
improve the economical production indexes and quality ofproducts. Special
emphasis is given to the effects that may beachieved by waste gases heat
utilization in which field nowadaysthe most significant reserves in the
rationalization of energyfuels use exist.
In the paper the method is suggested which proposes moresystematic and
complex access to the improvement of technical andeconomical
characteristics of the heating furnace energyconsumption, since it is
impossible to give a unique integraltechnical solution taking in
considerstion the specific problemsof each furnace in different
environments. For the sake ofoptimization one-dimensional mathematical
model of radiationrecuperator and sectional furnace has been developed
which hasdetermined their optimal technological, constructional and
energyparameters.
Keywords: Radiant Recuperator, Sectional Furnace, Mathematical Models, Heat Balance, Optimization
- Type of paper
: Ph.D.
Title: Three-dimensional Mathematical Model of Soldification and
Possibility to Predict Shrinkage Cavity in Steel Casting of Complex
Geometry
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Date of defense: 12/20/93
Language: hrvatski
Number of pages: 226
Summary: Three-dimensional mathematical model of solidification of
steelcasting of compex geometry in sand mold has been presented in
thepaper. An algorithm is obtained by means of numerical implicitBrian
method, and programmed in computer language ASCII FORTRANfor SPERRY 1106.
Simulation of solidification process isperformed for low-carbon steel
casting with 0,25 p.c. carbon andsand mold of known thermal properties. On
the basis of simulationthe solidification time and the way of
solidification can bedetermined, and together with model of temperature
gradient thepoint of occurrence and dimensions of shrinkage cavity in
thecasting. Mathematical models were experimentally verified bymeans of
measurement of temperature incasting and sand mold, andvisually (location
and dimensions of shrinkage cavity). Thecomputed results aggred relatively
well with the experiment. Theresults obtained enable to point in modern and
scientific way tothe point of occurrence and dimensions of shrinkage cavity
incasting of complex geometry.
Keywords: Three-dimensional mathematical model, Solidification, Steel casting, Sand mold, Shrinkage cavity
- Type of paper
: Ph.D.
Title: Mathematical Modelling of the Appearances in the Meniscus
Vicinity During Continuous Steel Casting
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Date of defense: 07/16/91
Language: srpsko-hrvatski
Number of pages: 126
Summary: The meniscus appearances during continuous slabs casting
havebeen investigated by metallographic technique and mathematicalanlysis.
The mathematical tests have shown that the oscillationmarks could be
classified according to the presence or absence ofsmall hook in the
subsurface structure. The positive segregationof the soluted elements,
especially the phosphorus ones have beentracted at the bottom of the
oscillation marks and have beenclassified into two types. The first type
has been tracted at theunder surface hooks, whereas the other type of the
positivesegregation is found at the bottom of the oscillation marks.
Thetransverse cracks occur along the bottom of the oscillationmarks. The
surface of the transverse cracks shows interdendriticappearances in the
vicinity of the slab surface which means thatthe cracks have started when
hot slab broke into the mould. It isshown by the theory of lubrication that
due to film geometry ofthe molten powder which is found between the
meniscus solidifiedshell and mould wall, considerable pressure gradient is
in acondition to deform the meniscus. The pressure gradient in themolten
powder is created by reciprocal mould progression inrelation to the slab
solidified shell. The surface balance offorces between steel and molten
powder is applied for calculatingthe meniscus as a function of the pressure
created in the film atdifferent stages of the mould oscillation cycle. This
shows thatthe contact point between the meniscus and the mould goes out
ofthe phase for 1/2f and has a large amplitude than the moulddisplacement.
By heat transfer analysis, the temperaturedistribution is predicted in the
infiltrated film between thesolidified slab shell and the mould wall.
Keywords: Mathematical modelling, Oscillation marks, Cracks, Segregation, Meniscus, Powder film, Pressure in film, Molten powder speed, Resistance force of molten powder, Powder consumption, Temperature in film
- Type of paper
: Ph.D.
Title: The Characteristics Properties Processing of Materials by
High Temperature Thermomechanical Processing
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Date of defense: 02/20/95
Language: hrvatski
Number of pages: 157
Summary: The paper encloses research of the properties of
characteristic highstrength woldable bainitic construction steel with
special reference to deformation resistance. Past knowledge about the
developement of construction steels with reference to up - to - date
production and processing procedures as well as possbilities of therr
application are presented. Mechanical properties and toughness of the
observed steel depending upon properties of thermomechanical processing are
elaborated. Required properties of the observed asrolled steel are reached
on the basis of its chemical composition and thermomechanical processing.
The proposed chemical composition and thermomechanical processing satisfy
the requirements. In the paper is presented the change of flow stress
(gield stress) depending upon test temperature, deformation rate and
deformation for austenitizing temperatures 1230, 1100 and 1050řC.
Microstructural changes depending upon test conditions are presented.
Keywords: Microalloyed structural steel, high strength structural steel bainitic structure, grain size, mechanical and technological properties, heatmechanical treatment, recrystallization, precipitation of carbonitrides, deformation characteristics, deformation resistence, mathematical experession for calculations of deformation properties
- Type of paper
: M.A.
Title: The behaviour of casting powders at heating and melting
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Author: IVANČAN ANKA
Date of defense: 01/10/91
Language: hrvatski
Number of pages: 75
Summary: In this paper the behaviour of casting powders at heating
andmelting during ingot and continuous casting in the Steel PlantSisak has
been studied. On the basis of laboratory testings ofthe behaviour at
melting in the as received and decarburizedconditions, in different
atmosphere and particulary at differentadditions the behaviour of cast
powders in plant conditions willbe predicted.
Keywords: Casting Powders, Heating, Melting, Behaviour
- Type of paper
: M.A.
Title: Influence of Iron and Another Elements on the Quality of
Aluminium Alloys in Processing to Die Casting
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Date of defense: 12/15/92
Language: srpsko-hrvatski
Number of pages: 136
Summary: The use alluminium alloy casting in the past decade has had
aphenomenal grown paralleling that of aluminium products ingeneral during
the same period. More and more traditionalmaterials are being replaced by
improved aluminium castingalloys.
Alloying elements, such lead, zinc, tin and sodium which havereletively low
melting points usually are added tod melt as puremetal to the aluminium.
Other alloying elements regularly addednickel, boron and beryllium. This
metals are usually added topure aluminium in the form of rich alloy ingot.
Permanent molding and die casting involve higher tooling charge,but unit
price is lower particularly for langer runs. Diecasting are extreme,
usually involving highest tooling charge andlowest piece price on large
quantities.
Alloys whose destined to produced "prirubnica" are AlSi12Cu andthis is a
light strenght alloy used for other components designedfor severe service
conditions. Fluidity is excellent, pressuretinghtness is very good and
resistance to hot cracking is good.This alloy has good machinability,
polished finishes are good andcorrosion resistance is good.
Influence of iron and another elements on the quality ofaluminium alloys in
processing to die casting "prirubnica"treating in study.
Keywords: Aluminium Alloys, Quality, Influence of Iron, Die Casting
- Type of paper
: M.A.
Title: The Steel for pipes in oil industry
Faculty: Fakulteta za naravoslovje in tehnologijo Univerza v Ljubljani
Date of defense: 12/20/91
Language: hrvatski
Number of pages: 94
Summary: In the study show showed view choice of materials for
productionpipes in oil industry in accordance with quality grades as wellas
possible the forms corrosion the pipes in service withespecially accent on
influence factors on sulfide stresscorrosion cracking. After series
variants heat treatment oftubings from low alloy Mn-V and Cr-Mo steel to
carried out isanalysis resistivity of pipes API quality grades C-90 and
C-95 tosulfide stress corrosion cracking and hydrogen embrittlement.
Therelation between the microstructure steel and hydrogenembrittlement
mechanism as well as places begining cracking areestablished.
Keywords: Steel pipes, Oil industry, Sulphide stress corosion, Cracking
- Type of paper
: M.A.
Title: Pig Iron Quality in Dependence of Technological and
Thermodinamical Conditions in the Blast Furnace Production
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Author: BALENOVIĆ MARIJAN
Date of defense: 02/11/92
Language: srpsko-hrvatski
Number of pages: 160
Summary: The definition of process parameters making influence to
the quality of iron with application of personal computer and program
package based on the mathematical statistics method, represents one of the
ways for mastering and improvement of the general iron quality. The
offected data processing, covering a longer time period, on the
investigated aggregate, indicates one unstable technological process based
on the unprepared(raw) charge and low blowing temperature parameters. This
causes a low utilization of gas reduction capability, higher participation
of direct reduction, low production and high coke consumption. The analyses
of iron quality and distribution of the particular elements between iron
and slag in the suitable reduction atmosphere, point out the importance on
maintaining the thermal conditions within the furnace chamber as on
important cause of iron composition variation. The evaluation of the
parameters influencing the production and iron quality indicates the
necessity of: benefication of ore stopping, homogenization of charging
materials, increase of temperature and blowing air, proper selection of
slag quantity, corrections or changes of current desulphuration method,
introduction of accurate and fast quality control during the production
process, introduction of information system for the monitoring and planning
the iron production. The improvement of average obtained values of
influencing parameters within these raw materials and technological
conditions of production in Iron Works Vareš will provide the decrease of
dry coke consumption by 55 kg/t of iron, increase of production by 12,45%
and iron production of considerably higher quality.
Keywords: Blast furnace, pig iron quality, influencing parameters, statistic methods, personal computer.
- Type of paper
: Mentorship
Title: Pig Iron Quality in Dependence of Technological and
Thermodinamic Conditions in the Blast Furnace Production
- Authors:
- Krajcar, Josip (23143)
- Dmitrović, Radana
- Iharoš, Ana
- Novosel-Radović, Vjera (33706)
- Ivančan, Anka (79316)
- Đuričić, V.
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Mentor: MARKOTIĆ ANTO
Date of defense: 02/11/92
Number of pages: 160
Author: Boras Ivica
Degree level: M.A.
- Type of paper
: Mentorship
Title: Influence of Iron and Another Elements on the Quality of
Aluminium Alloys in Processing to Die Casting
- Authors:
- Krajcar, Josip (23143)
- Plepelić, J.
- Butorac, Juraj
- Ivančan, Anka (79316)
- Iharoš, Ana
- Vuković, Dušan
- Ferketić, Vladimir (11634)
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Mentor: MARKOTIĆ ANTO
Date of defense: 12/15/92
Number of pages: 136
Author: Kazazi Gezim
Degree level: M.A.
- Type of paper
: Mentorship
Title: Pig Iron Quality in Depence of Tehnological and
Thermodinamic Conditions in the Blast Furnace Production
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Date of defense: 02/11/92
Number of pages: 160
Author: Boras Ivica
Degree level: M.A.
- Type of paper
: Mentorship
Title: Influence of Iron and Another Elements on the Quality of
Aluminium Alloys in Processing to Die Casting
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Mentor: MARKOTIĆ ANTO
Date of defense: 12/15/92
Number of pages: 136
Author: Kazazi Gezim
Degree level: M.A.
- Type of paper
: Mentorship
Title: Three-dimensional Mathematical Model of Soldification and
Passibility to Predict Shrinkage Cavity in Steel Casting of Complex
Geometry
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Date of defense: 12/20/93
Number of pages: 226
Author: Grozdanić Vladimir
Degree level: Ph.D.
- Type of paper
: Mentorship
Title: Possibilities of control of melt heating in open-hearth
furnace by means of continuous follow up flue gas analysis in the vertical
canal of furnace head
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Mentor: ČRNKO JOSIP
Date of defense: 01/09/91
Number of pages: 115
Author: Kundak Mijo
Degree level: Ph.D.
- Type of paper
: Mentorship
Title: Possibilities of control of melt heating in open-hearth
furnace by means of continuous follow up flue gas analysis in the vertical
canal of furnace head
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Mentor: KRAJCAR JOSIP
Date of defense: 01/09/91
Number of pages: 115
Author: Kundak Mijo
Degree level: Ph.D.
- Type of paper
: Mentorship
Title: Mathematical modelling of the appearances in the meniscus
vicinity during continuous steel casting
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Date of defense: 07/16/91
Number of pages: 126
Author: Risteski Ice
Degree level: Ph.D.
- Type of paper
: Mentorship
Title: The behaviour of casting powders at heating and melting
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Date of defense: 01/10/91
Number of pages: 75
Author: Ivančan Anka
Degree level: M.A.
- Type of paper
: Mentorship
Title: Contribution to modelling and optimization of material
heating process in rolling mill heating furnaces
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Date of defense: 03/16/91
Number of pages: 173
Author: Lazić Ladislav
Degree level: Ph.D.
- Type of paper
: Mentorship
Title: The steel for pipes in oil industry
Faculty: Fakulteta za naravoslovje in tehnologijo Univerza v Ljubljani
Mentor: MAMUZIĆ ILIJA
Date of defense: 12/20/91
Number of pages: 94
Author: Gojić Mirko
Degree level: M.A.
- Type of paper
: Mentorship
Title: The Characteristic Properties Processing of Materials by
High Temperature Thermomechanical Processing
Faculty: Metalurški fakultet u Sisku Sveučilište u Zagrebu
Mentor: MAMUZIĆ ILIJA
Date of defense: 02/20/95
Number of pages: 157
Author: Križanić mr Rade
Degree level: Ph.D.
- Type of paper
: Survey/Study
Title: Reseaching Result Applied on Rolling Conditions of Strips
in "Strip and Billet Rolling Mill - Željezara Sisak" Sisak
- Authors:
- Križanić, Rade (23663)
- Mamuzić, Ilija (27862)
- Nikolić, Đurđica
Ordering party: Valjaonica traka i gredica "Željezara Sisak" Sisak
Institution depot: Istraživačko Razvojni Institut "Željezara Sisak" Sisak
Year: 1991
Number of pages: 58
Language: hrvatski
Summary: Technological process of strip rolling in strip, billet
andseamless tube rolling mill in Željezara Sisak are defined. It
wasestablishmed that the most favorable conditions are acheavedwhile
rolling the strips in 6 rolling mill stands.
Keywords: Roling of strips and billets, bainit steels, deformation resistence, deformation, rolling programme
- Type of paper
: Survey/Study
Title: Results of Resaching on Torsion Plastometer Conditions of
HighstrengthWeldable Construction Bainit Steel H-75
- Authors:
- Križanić, Rade (23663)
- Mamuzić, Ilija (27862)
- Nikolić, Đurđica
Ordering party: Valjaonica traka i gredica "Željezara Sisak" Sisak
Institution depot: Istraživačko Razvojni Institut "Željezara Sisak" Sisak
Year: 1991
Number of pages: 60
Language: hrvatski
Summary: The investigating results of steel, grade H-75,
deformationresistance obtained on torsion plastometer, formulas
forcalculation and tehnological conditions for performing of rollingprocess
on continuous train in Željezara Sisak in Sisak areshown.
Keywords: Torsion Plastometer, Construction Steel, Bainit Steel, Deformation Resistance
- Type of paper
: Technical report
Title: Symposium of Croatian Metallurgists
- Authors:
- Hensel, Arno
- Mamuzić, Ilija (27862)
Ordering party: Hrvatsko metalurško društvo
Institution depot: Hrvatsko metalurško društvo
Year: 1994
Number of pages: 1
Language: njemački
Summary: Symposium of Cratian Metallurgists SCM 96.
Keywords: Symposium
- Type of paper
: Technical report
Title: 2nd International Symposium of Croatian Metallurgists
- Authors:
- Mamuzić, Ilija (27862)
Ordering party: Hrvatsko metalurško društvo
Institution depot: Hrvatsko metalurško društvo
Year: 1995
Number of pages: 3
Language: engleski
Summary: 2nd International Symposium of Croatian Metallurgists
Keywords: Symposium
- Type of paper
: Radio broadcast
Title: